This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hello,
I am using nrf52832 as a peripheral and running SD S132. l am looking for an ble peripheral example wherein the Out of Band security level is used.
Can you point...
Using Programmer v4.0.1 can successfully read the NRF51822AB, but upgrading to the latest version 4.4.2 results in a failure to read the device.
Additionally, after...
We are working with nRF52840 and NCS2.6.1. And we want to change pin configuration for UART1 instance during the runtime and we have also used following ASYNC UART configuration...
Hello,
I am trying to upload certificates to my nrf9160 chip on a custom board. I have done the following: 1. Loaded AT_CLIENT from the samples
2. Tested all AT commands...
Hi
we are using the BT HCI to add BT functionality to nrf9160 using the thingy91 hardware. upon updating the sdk from 2.7.0 to 2.8.0, we are getting the error bt_hci_core...
I want to read and write data such as incline and resistance from the Zwift app using my nrf52dk device. Based on the information I found online, it seems I need to communicate...
Hi,
My custom NRF52840 device has two interfaces (UART and USB) for host connection. I have successfully verified firmware upgrades using mcumgr from a mcuboot via the UART...
Hi
Use the following routine NRF\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs.
Use IOS APP Enable the data to be sent once...
When evaluating BLE mesh with multiple nodes the nRF52840 Dongle is perfect to keep cost and physical size down.
I thus have one nrf52840 DK and a couple of nRF52840 Dongles...
We can get the active end points and list of cluster in end points.
But is there a way to get list of attribute and types of attribute in each cluster?
Hi community,
I read these articles about match network for antenna:
General PCB design guidelines for nRF53 series - nRF5x - Hardware design, test and measuring - Nordic...
Hi,
Like some other users, I face an issue migrating from ncs<2.6.0 to ncs 2.7.0 regarding radio notification.
I saw it is possible to use the PPI for the EGU IRQ to be...
Hello, I am using the Soft Device S140 7.3.0 with nRF5 SDK 17.1.0 and the nRF52820 as a peripheral in an NUS application. Initially, the transfer was slow but worked perfectly...
Using the nRF54L15 Development Board.
Did try to run the "nRF connect for desktop" - "Quick start"
I do not get a reply from the Board when doing one of the samples. ...
