I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
I want to read the RSSI. The code is shown as follows: ，However, after compilation, the error message displayed is: "undefined reference to `bt_hci_cmd_alloc'".I need to know...
Hi there,
I am seeing inconsistencies with the PCB layout specification of the nrf7002.
1) In the v1.1 of nrf7002 datasheet, it is recommended that the following capacitors...
Hello, we are currently testing the output of square waves through GPIO output pins. However, I found that a single operation to set the GPIO output pin high or low using...
I've installed the same version of the Power Profiler V4.3.1 on Linux and on windows.
On windows the device gets recognized straight away and I can use it, on Linux however...
If I understand correctly, you can pretty much assign any pin to any peripheral. I've been using a modded central uart project on a dev board but on this other board I'm using...
Hello,
is there any way to access the Stack and Heap Start/End memory addresses from the zephyr code?
I have found the __INITIAL_SP definition that gives the Stack start...
Hi,
I have been working through the Dev Academy cellular course using the nRF9151 DK which is fitted with a 1NCE MFF2 eSIM. I was able to set this up in the Board Configurator...
Hello Team,
I am using the nRF52833 with the nRF Connect SDK (v2.9.1) in VS Code , and I am experiencing an issue with the RTC calendar update.
I initially set the RTC...
Hi everyone,
After a debugging session using the debug tool in nRF Connect SDK with an nRF52832 on a custom board, the chip is now completely unresponsive—I can't flash...
Hi, Recently we upgraded to nrf-sdk 2.7.0 (previously on 2.6.1) and I began to notice that NFC had stopped working for our project, when running on nrf5340dk.
While switching...
To preface:
Board: nRF9151DK
nRF Connect SDK / Toolchain: 3.1.0
Hello,
I am attempting to learn and integrate full modem FOTA functionality into my application...
Bonjour,
We are working on a firmware upgrade for our product based on a nRF52833.
With the previous firmware, compiled with SDK 2.3.0, when the board was OFF, the power...
HI
I am using the NCS 3.0.0 SDK and want to use FCB to store sensor data only in external flash.
Therefore, I added external flash to the pm_static.yaml file in the project...
