Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
I have an LED connected, and I want to use PWM, but enabling it adds about 700 µA of passive current — both when the output is high and low. However, if I set the duty cycle...
Hi,
I'm developing on the nrf5340 and the semtech LR1110. I'm using the latest SDK version 3.1.1.
I saw in the SDK that there's a library for the LR1110, but I can't activate...
Hi.
I try to build the example Matter: light bulb and in the terminal shows an error that iI don´t underestand what is the problem.
Please ¿Any could explain me why ocurs...
Hi,
I am using the Thingy:91X device and can see the updates appearing on the hello.nrfcloud.com web application, but I would like to have access to the 'device' via the...
As the title said, I'm currently on the nRF21540 DK. I turned on Async UART:
CONFIG_UART_1_INTERRUPT_DRIVEN =n
CONFIG_UART_1_ASYNC =y
CONFIG_UART_1_NRF_HW_ASYNC =y...
Hey Nordic Team
Just looking for guidance and clarification on the nPM1300 setup. couple of questions on the sample setup below.
Project Overview
Project is a consumer...
I setup 2 Holyiot nRF54L DK Development Boards with the channel sounding sample code from NCS 3.1.1 samples/bluetooth/channel_sounding_ras_initiator (initiator and reflector...
We have designed a custom board around nRF54H20 EngC revision and testing it on NCS 3.1.1. We were able to do provisioning and bring up using iron-side binaries. But got two...
Hi all,
I’m planning to add crypto support to my nRF52811 application. My main requirement is encrypting and decrypting a string , but I’m hitting flash size constraints...
Hi，
I am using the nrf52840DK development board and running the SDK of version ncs/v2.6.0. When I flash the samples/esb/esb_ptx and samples/esb/esb_prx projects onto the...
Hello,
I recently tried some examples with nRF53 + nRF7002 (e.g. ble_coex example).
However, I am developing with nRF54 and I would like to understand if the combo nRF54...
Hello,
I am new to embedded programming and I'm trying to create a small application that uses BT advertisements. I've tested my code on an NRF52840 dongle, and a board...
Hello,
we made a circuit board with nrf5340. We only burned the blinky program once for testing and it was successful. However, when we tried to burn the program again,...
Hello everyone,
During the design of my core board, I encountered an issue where after flashing a demo program, the core board cannot be programmed again. The demo program...
