Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I'm trying to run Provisioner Example on my nrf52840 DK, which is in examples/provisioner directory, . First I've build softdevice on DK and then I'm trying to build provisioner...
Hey NordicSemi. In my new project, I use DK NRF9160 and I need to determine the location. Since hardware GPS does not work, I decided to use the detection of coordinates through...
Hi,
Something locks-up my I2C sometimes and I need to make I2C recovery. It looks like Nordic has not implemented the zephyr i2c_recover_bus function, so I guess I need...
I'm looking for dual core inter task communication examples
where a thread on one core is interacting with a thread on the other core ?
e.g. will there be some kind of...
Hello All,
I was looking at the Digi XBee3 modules for a ZigBee project I am working on. What is great is they allow you to write MicroPython code to control the network...
I am trying to send some values from nRF52810 Board to my Laptop. I am using a nRF52840 Bluetooth Dongle to connect the board to my laptop. I am using the "Heart Rate Collector...
Is there a way to get the values of CompanyID ProductID & VersionID before provisioning? I'm working on my android application using the nRF Mesh Library and after identification...
Hello, I work on nrf9160 dk and i try to get tx power: For exemple, with a RSRP -76 dbm i get this consommation curve (read current on P24 throught 0.5ohms resistor):
and...
Hello,
we are developing a HID slave device. we need to support five cell phones connect and bond with the device not at the same time.
we use the ble_hid_keyboard example...
Hi,
I am check this code: https://github.com/NistantriTech/ibeacon_nrf52/tree/ed938973c9a8ebd4f0bb91a3689e5d8242980681
It used SDK15.0
On Ebyte 52832 - and face problems...
Hi
After trying out nRF5340 step-by-step guide we'd like to learn nRF52833 following similar step-by-step start-up guidance if such exists.
I guess for the basic operation...
Hi all. I am using the twi_sensor example of the sdk12.3 in a NRF51822 Taking a look on the tx function: err_code = nrf_drv_twi_tx(&m_twi, MXC400_ADDR, reg, sizeof(reg), false...
Hello ,
we know that, when initialize a BLE slave device ,we need to define the BLE MAC address type.(we need to write our owen address ,not usig the original ble address...
