Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hello,
Our project:
At the moment we are developing an application with a nRF52840DK as central and a nRF52DK as peripheral. The code on both boards is based on the ble_app_uart_c...
Dear All,
I have chosen NRF9160 device for two requirements - SMS transmit or receive and LTE IOT connectivity [Both are different project requirements].
After going through...
As I know, nRF52 series is produced in the TSMC on 55 nm ULP process. But I can't find any info about the integrated circuit manufacturing process of nRF53 series. Could you...
Hi, I use a nRF52840 with the nRF Sniffer Firmware for capturing advertisement frames and connections between several devices. My question is if it’s possible to capture communication...
I'm writing custom boot loaders. One of the capabilities is to update the network processor from code running on the application processor. The PCD subsystem looks like it...
On 3/11, we received a message from the Nordic "HomeKit Team", announcing that HomeKit support in now integrated in the latest release (ncs 1.5.0) and distributed through...
chip - nrf52840 sdk - nRF5_SDK_15.3.0_59ac345 softdevice - s140nrf52611
Issue enabling usb cdc without softdevice enable.
The COM port does not show up without the softdevice...
Ring buffer operates on uint8_t , but I would like to use ring buffer to store 16 bits ADC data. What is the simplest solution?
Converting 16 bits data into 8 bits, store...
Hello, Guys!
As I know, the Bootloader uses RTC2.
The problem is that RTC2 continues to operate after executing the bootloader, in my Application.
My Application not...
We are using nRF52840-DK and we need to stream the audio to our iOS app that we are developing. But currently, we are not able to get the audio streams back for mic to iOS...
In my application we have an ADC input pin which we want to connect to comparator input too. Based on the highlighted statement in section 7.6.1 Can the same analog pin be...
Hello,
since a few weeks I have the following problem with the nRF Connect for Desktop app on Linux (Arch Linux specifically). The runner launches and I can install and...
Hi,
starting the NCS v1.5.0 "Bluetooth: EnOcean" sample on nRF52840 DK, the following error occurs:
Bluetooth init failed (err -35)
Any suggestions? Thank you.
Hello
I'm testing multiple frequencies to ensure smooth ultrasound control.
Frequency can be generated via 'APP_PWM_DEFAULT_CONFIG_1CH (period, pin)'. But it seems difficult...
Hello there
I hope you are doing well
I am looking for rf module that meet my requirements, please check these requirements below and give me any of your product meet...
