Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello everyone,
I have done researches on the forum but I did'nt find any answer. I would like to programm the dongle througth the SWDio and SWDCLK of the Dk.
1) is it...
Hi, I'm designing water meter modem using the nRF52840 + nRF9160. I will apply nRF52840 as a HOST CPU and the nRF160 contol by nRF52840. (please refer to attached picture...
Hello,
I am interfacing a NRF52832 with a PCF8574 I2C slave using SDK 15.0.0.
As per the datasheet, the device will send the data to the slave after it receives the write...
Dear Sir,
I designed a new pcb based on nrf9160,
The boards are populated with cipsim.
When running the MQTT_SIMPLE project i get the following error for the 2 boards...
Hi,
We are upgrading our product from SDK 15.0 to SDK 17.0.
In the old SDK there seems to be one file abailable: ../SDK_15/External/nrf_cc310/lib/libnrf_cc310_0.9.9.a...
Hello:
We are developing a DFU bootloader for an NRF52 product that supports USB and BLE upload methods (they are 2 separate bootloaders from a common source). Both work...
I am hoping to pass data from the nRF52840 to the nRF9160 over UART_0, on a custom PCB. For context, the aim is to pass data at a rather quick rate and good reliability. The...
HI,
I want to make a receiver to get BLE packets on any channel.(NO SOFTDEVICE)
I fail to fullfile it yet by reading <nRF52810_PS_V1.3.pdf>.
Any other hands can give...
Hi,
I am working on the asset_tracker application example on a Thingy:91 device. As I understand it, to activate the GPS it is necessary to keep the button pressed for a...
Hi,
In nrf9160 I want to check the communication of LTE device.
I have installed nRF Connect for Desktop, Getting Started Assistant, LTE Link Monitor, & Programmer.
...
Dear,nordic:
Please help me solve the exception encountered during the MQTT connection
SDK : ncs v1.2;
samples : asset tracker;
path : ncs\v1.2.0\nrf\applications...
Hello everyone a basic question but just to be sure.
I would like to make a custom board and I want to program this board with segger Embedded studio, should I just have...
Hi!
I managed to get the device connected to the nrfCloud and started receiving messages from it.
Anyway, the embedded antenna cannot catch the signal very strongly. Can...
Hi,
I am trying to test the asset tracker code on the nRF9160DK from the precompiled hex files from [ images_dfu_hex/nrf9160dk_asset_tracker_dfu_2020-04-29_bc7ade8b.hex...
