Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello, we have made cars that play laser tag against eachother using infrared emitters and receivers. The problem is that the infrared radiation bounces off the surroundings...
Hello i have a rigado BMD-300 module and i would like to flash a new version of softdevice app and bootloader but i want to protect the UICR memory because that is where the...
Hi my goal is to put the NRF into system on low power mode every other second. I have a repeated app_timer that increments counter variable m_custom_value every second. I...
Hi,
I am developing a project using the nRF52840 DONGLE. As part of the process, I need to be able to debug my code, so I am using IAR and a J-TRACE PRO for that. The...
I am using NSDK 15.3, MeshSDK 3.2.0, SoftDevice 6.1.1 and nRF52840 DKs.
I successfully integrated the DFU capabilities in my firmware that uses BT Mesh. I am downloading...
I'm studying nRF52811 manual, there are moments not clear to me:
1. Is I/Q sampling paused during SWITCHING slots? For example, if I configure 16 1-msec slots (8 switching...
Hello again Nordic Pros,
I am trying to get some debug logging going using the 52DK running ble uart central under SDK 12.3 and RTT Viewer v6.4.
I have setup config.h...
Hello, I do connection between one nRF52840 (central / NUS) to multiples nRF52840 (peripheral NUS)
in my function static void on_adv_report(nrf_ble_scan_t const * const...
Hi Nordic Developers,
I would like to extend my question on creating vendor specific model from this question I posted earlier (extension of Thingy Mesh Demo v0.1):
https...
Hello Nordic Pros,
Doing some debugging using RTT Viewer and an nRF51822 under SDK12.3. Here is the code lines of interest:
And here are the log messages:
iDrink:...
Good afternoon!
We're considering an off-the-shelf nRF52832 based device for our needs.
the application will likely involve two nRF5283-based devices fitted with external...
Dear All,
On the http_application_update after the download is complete, in order to run the new firmware the user needs to press the reset button.
I would like to be...
As in another post , I was looking for a way to change the TTL per message. Is there a reason that it can only be changed per model? I can imagine the TTL being part of the...
Hello,
I'm trying to use the mesh DFU on 2 nRF52840 DK by following the quick start guide and it didn't work.
Using the mesh sdk 2.0.1 I made the below batch file as described...
