Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hello,
I have a bootloader with a low power wait for power button on startup.
When I do a BLE DFU update of bootloader + SD + appli, the Nordic smartphone application...
hi
I have a application use NRF52832 to scan beacon's advertising and write the advertising data into NRF52832's advertising.
I found the working current is nearly 3mA...
Hello,
I am useing NRF51822-QFAC in my BT bridge project; Now I need to design the matching circuit; there was some recommended matching circuit in the datasheet(11.3--11...
I have a central device that uses BLE to scan for a specific device (there is only a single device it can bond with). Right now it checks the UUID and the mac address of all...
my device giving output as square pulses.but would like to control current from the range 50uA to 500uA of square pulses.how to calculate it. can someone help me
Hi,
I have a question that Product Specification v3.1 of nrf51822 describes Flexible Power Management: 2.6 μA at 3 V ON mode, all blocks IDLE. But, in the same place, NRF52832...
Working on migrating my application from sdk 12.2 to sdk 14
except for some flash issues most of it seems to be working as before, except I notice this message in jlink:...
Hi,
I'm using SDK 14.2.0 flash_fstorage_example_s140_pca10056 with SEGGER on the nRF52840 Preview DK.
As you can see the basic example not working, what I'm writing...
I got the ble_app_lbs example working using SDK 8.0.0, and am now trying to integrate it into my existing project which was based off of ble_app_rscs using SDK 11.0.0.
...
Hello,
I am trying to intergrate the blinky, timer, and UART examples.
Blinky and Timer examples seem to work fine.
When I added UART, linker error starts to show up...
Hi,
Follow answers from here and have many try, not success yet.
Development with GCC and Eclipse, can not reach main() but return "Programe file does not exist" when...
Honorable technician, hello
I am adding a dependency Library for DFU by Android studio,find " compile 'no.nordicsemi.android:dfu:1.3.0' "and “ implementation 'com.android...
As the title says, I'm having problems connecting to my device with my custom board and I don't know what else to do. This is my Layout:
Whenever I upload my firmware...
I found nRF52832 modules like www.ebay.com/.../332270581440 on eBay, but there's no documentation for them except the board pinout. Has anyone tied them? How are they shipped...
