hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi!
There are many questions about flash memory already.
But I could not find the question I wanted.
I want to save scan data to flash memory.
However, when you...
As a peripheral,S130 can work ok,but when I add a central role, there is a error at central start to connect a peripheral. err_code = sd_ble_gap_connect(&addr,&m_scan_param...
When a peripheral advertises on one of the three advertising channels, does it listen for a short duration on that channel (as implemented by the Softdevice?) And then repeat...
Hello.
I am measuring the current of nRF52832 using Power Profiler Kit(PPK).
I used the following case with PPK setting.
infocenter.nordicsemi.com/index.jsp
At...
Hello Folks,
I am using PCA 10056 Eval board. I am using SPIM0 to connect 5 slave sensors. The Chip select is done by the UART Tx pin. So If I send 0x01 over UARt then...
Review_4Jan.zip
Hello All,
Please review the attached revised schematic and give your valuable feedback.
Please find below queries:
In case you want to know the...
Hii everybody,
I want to do ble pairing(nrf 52832 development board) with android phone. after searching on nordic devzone how to pair device i found that pairing mechanism...
Hello all,
I have below queries on my custom board and mesh.
I have designed my custom board using nRF51824 and i am using J link debugger for programming , I can able...
Hi, I know there are already lots of threads around this but it seems none is like mine.
I'm running my toolchain on a Mac so I think I have a more challenging debug setup...
Hi,
I would like to know is there any shopping sites selling beacon modules that we can configure later based on our requirement?
I searched on few shopping sites where...
Hi,
We are developing a pretty complicated multi-threaded application on nRF52832.
Part of the requirements are storing a large amount of data over time (Megabytes)...
Hi
I am using gpio for input interrupt as below
nrf_drv_gpiote_in_config_t in_config = GPIOTE_CONFIG_IN_SENSE_HITOLO(true);
in_config.pull = NRF_GPIO_PIN_PULLUP;
...
According to PS, external reference min. voltage is 0.83V. However, I've experimented with voltages of about 0.2V and it appears to work. Specifically, I connected a voltage...
