hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
When programming the bluetooth mesh light control demo example found in the bluetooth mesh SDK, i get this error using J-Link RTT Viewer:
0> <t: 0>, main.c, 116, -----...
As I know, I need to do watchdog feed on bootloader.
but what If watchdog reload value is long enough for DFU?
for example, if DFU via BLE takes 2-3 minutes, generally...
Hi,
I am using IAR embedded workbench IDE - ARM 8.20.1 (full version) to compile the SDK 14.0 blinky_pca10040_s132 -nrf52832_xxaa example. However, I got some errors which...
I'm currently using nRF Connect (windows), in conjunction with the PCA10028 board, as GATT server so I can provide a default test service to be consumed by other devices under...
Hi
An unprovisioned device will advertise a beacon and the spec says that it shall be advertised with non-connectable and non-scannable undirected advertising events
...
Hello there,
for a project I would like to use the Arduino Primo core with the nRF52832 chip to read a NFC Tag.
I could not figure why it can´t read a tag even though...
Hi,
I've test the light_control example with the PCA10028 & PCA10040 recently. The PCA10040 was test and it works normally, but the PCA10028 does not.
I have also checked...
I am working on an application that allocate data dynamically at initialization, and my malloc/calloc returns NULL a lot earlier than I expected.
Using a debug macro, I...
Use the E: \ Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart \ pca10040 this routine
Run to chart a breakpoint on the resumption of here
...
Hi guys,
I'm trying to use the HFCLK to generate high resolution timing. Ideally at the millisecond resolution. I've written a layer around the nrf_drv_timer.c module....
Hi,
I followed the tutorials you made to start developing BLE applications for nRF52 series development board. Then I started to make my custom application (in fact, it...
Hi everyone,
I have been reading the Specifications of Bluetooth 4.1, mostly about Universally Unique Identifiers (UUIDs) for Services, Characteristics, etc.
I found...
Respected sir,
setup for programming = Eclipse-gcc-toolchain-setup
board = PCA10040
as per my way first take a ble_app_uart code startup my coading purpose.
then we...
Hi Guys,
I'm doing the following before putting my device to sleep. This works fine when I use NRF_POWER->SYSTEMOFF, but when I use sd_power_system_off(), it doesn't seem...
Hello,
I am using nRF52832 development kit. I used different examples to send data. But i couldn't accomplish to send data packet over 20 byte. The max data size is defined...
