When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hello,
i'm looking for the NRF52832 QFN48 6x6 symbol and footprint in Orcad/Allegro format to accelerate my design,
unfortunately, my electronic designer don't use Altium...
I've been experiencing this bug for a while now. What happens is that a app_timer's overflow handler can't put any more messages into the queue because the queue is full,...
I need to connect to the VSS of the nRF52832-CIAA Ground
A mistake by one of the VSS was not connected nowhere.
The VSS was one N.C..
Do you have any problem with...
im sure the reference design is copywritten if i added two components and removed the GPIO breakouts and switches and led is that in any way not ok? i know nothing on RF signals...
Hi. I am trying to add DFU service to sourse code with existing service. When I try to run service without device manager + DFU or run device manager + DFU without my service...
Hello!
I am trying to build a connectable Eddystone beacon with a Blend Micro board which uses nRF8001 . I used the BLEPeripheral library ( github.com/.../arduino-BLEPeripheral...
Should I call app_sched_execute at least once before the first app_timer_start ? I have a strange bug and I realized that calling it before is a fix but I don't see this in...
Maybe this is a newbie question but, I read that using TEMP is a restricted resource for the SD but I could not find any driver or example to use it correctly.
Can someone...
I am trying to determine the suitable set-up to determine when my system's battery source (lipo battery) is too depleted.
I am running my nrf52 at 3 volts and the Lipo Battery...
Hi. I try to fusion 's130_nrf51_1.0.0_softdevice' and 'flash write'. I checked flash write. but when i implement flash write with s130 softdevice, it is not working. If i...
I have the nRF52 dev kit, and I hooked up pin 13 to SDA and pin 18 to SCL on an I2C device. There are no external pullups on the SDA or SCL lines.
However, the TWIM module...
I tested some features of the new nRF Connect application version 1.0 on PC. The application has a lot of interesting features useful to develop and debug embedded software...
Hello Everyone!
I want to make a project that will recognize some tone in the air, up to 5KHZ, and will send nrf8002 a message as a result.
I though to use the nrf52 proccess...
