Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
I'm trying to lighten the leds using ble, my problem is that when I measure the current consumption when the leds command sent, it reaches to 5mA which is not suitable for...
Hi
I've playing around with the new peer manager a while. I used the example "ble_app_hrs_rscs_relay_pca10028.uvprojx" from the SDK10. After a first fix (see Link ) in...
Hi,
I want to use timer1 or 2 interrupt ISR to generate complicated PWM signal.
but the timer->intenset setting cause ble connection drop problem.
Please refer to my...
Hello. I'm having the following connection module with nRF51822 chip.
It was purchased here .
I've found example sketch for Arduino but i can't understand how to wire...
Hi,
I have been developing using some development modules from WaveShare (based on the nRF51822 QFAC) and they work fine.
However, I'm now trying to use a module better...
Hi Nordic Expert,
I am Alex and have been developing with NRF51822 for a long time. Thanks for your quick help before. Now our product bases on S110-7.1.0 and SDK-6.1.0...
Hi
i wrote the program which is making pulse one time on channel 0 and then followed by channel 1 and then again channel 0 and then 1 going on , my aim is to create pulses...
Hi all,
I am tring to connect more than two peripherals to contral device.
I am using sdk10 and three evaluation bords nrf51822.In on device i debbuged the code of uart...
My problems with Eclipse Luna continue. Going on holiday for a week I assumed the good fairies would sort it out, but no,,,
Anyhow, I'm sure it's some path error somewhere...
I'm trying to figure out something I'm seeing. I've modified the relay demo in the nRF52 SDK so that when I press button 2 on the board, it destroys any connections, erases...
Hello Everyone,
I have configured gpio pins for buzzer pin6 and pin 7 and am trying to clear those pins after buzzer making the beep sound but it is not getting cleared...
hello there i downloaded nRF51_SDK_10.0.0_dc26b5e.and run this example experimental_ble_app_blinky_s110_pca10028. here when i write 1 from master control panel LED turn on...
Hi,
I've asked a couple of questions around this before but that was before I thoroughly researched into what I was actually asking.
I would like to attempt to use the...
