Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Now, I'm using "nRF51\peripheral\temperature" example to test something for my nRF51 DK board.
I have upgraded sofeDevice s110 v8.0.0 in DK and I can use Keil "Download"...
I am using Unity3D BLE Plugin by Shatalmac ( www.assetstore.unity3d.com/.../ . Upon using the example code, it is discovering the UARt custom service, but dont know why it...
I am really struggling getting anything to work on my revision 1 module and as it has nothing connected at this moment all I can use is BLE or UART to observe any function...
Hi,
I would like to change the the advertising interval of the beacon kit in the sample ble_app_beacon app; however, I could not figure out where this parameter is. I see...
Hi,
I want to connect a rotary encoder.
So I have 2 pins of the nrf51822 connected to the encoder and I have to check which one change first to increase or decrease the...
So there seems to be a conflict between the TWI and the Softdevice. My I2C communication works over TWI fine in isolation but when i try to send data over ble the TWI doesnt...
I am using the nRF24le1 in Enhanced Shockburst mode.
The datasheet describes how it is possible to upload acknowledge packets, W_ACK_PAYLOAD, to the TX FIFO. And then the...
Hello,
I need to get RSSI with the NRF51422 (pca10031, S110), but i don't want to connect with a central device (i.e. Smart Phone). The central device should scan for bluetooth...
We tried to pair with and connect to nRF51822 DK running HTM app with SONY VAIO fit15e NB and always fail as we did the following steps.
We also tried some devices like ASUS...
Hi,
I just replaced the BLE chip in my board from CC2540 to nRF51822. I simply want to know how to configure the interrupt on a pin as well as rising/falling edge interrupts...
What are the allowed channel numbers for gazell?
In the gazell user manual it states, a possible 80 channels.
While the nrf_gzll_set_channel_table () API reference says...
Hi,
Is it possible for me to completely copy the antenna design from PCA10028 unto my custom board? I don't need a very long range, but I need to make a design fairly quickly...
For PCA10001 have 16MHz crystal, and I use the NOP to test the cycle. And found the device work in 16MHz. How to set this board as 32MHz?
This is my current setting in...
