I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
Hello friends, I am using nrf52833 MCU for my current project, this project involves a sensor from infineon that operate on SPI and it supports high frequencies up to 50 MHz...
Hi,
I referred to the DevAcademy FOTA over Bluetooth Low Energy, but in the provided code, the BLE mobile app connects to the device and it automatically enters DFU mode...
on cannot connect to the on-board Jink of the NRF52840DK board
I have tried:
Updating to the latest Jink driver
installed nrf connect tools for windows
connecting...
Hello,
I'd like to develop a BLE OTA Bootloader using the NRF Connect SDK, but I need to program my NRF52840 with a Serial Wire debugger. What tools do I need? Is there...
Hey,
Im have a thingy91 and multiple nrf52840 pcbs.
my goal is to make the thing91 a central device that reads data from the nrf52 devices and sends it over to the cloud...
We have a custom board with an nRF7002 controlled by a non-Nordic MCU. The WiFi drivers were ported from SDK 2.7.0, and WiFi in general is working, this question is about...
(I am a beginner) Hello, I recently got the Nordic nRF52840 dongle so I can sniff BLE packets from some devices I have. I set up the dongle following the recommended setup...
Hi,
What is the voltage on nRF52811-CAA chip DCC pin (A5)?
Can the regulated voltage on this pin be used as a voltage source to supply some external circuits?
Please...
Hi,
I am using nRF52811-CAAA bare chip on a standard 2 layer FR4 board and want to design a PCB trace antenna for it to achieve overall x100-200m range.
Is there an example...
Hello everyone,
we are currently designing a PCB based on the nRF52840. The system is dependent on high accurracy of HFXO.
In an old blog post on the TI forum I found...
Hello expert. My computer is windows11 system, using ncs+vscode for development, Jlink software version is V8.10c. My development board is nRF52840(PCA10056). The problem...
I appear to be running into an issue whereby I cannot see my device connected in VS Code using the nRF Connect for VS Code extension.
I have followed all the steps to set...
Hi nordic,
I have successfully completed the Bluetooth over-the-air upgrade using the secure bootloader example. However, we need to add an additional upgrade method. In...
I am trying to add s2opc to my project. But everytime i try to open the complete Workspace in VSCode, the nrf Connect extension, just does nothing. How to reproduce. Take...
I'm thinking of incorporating a TWI slave with nRF52832.
I'm using SDK 17.0.2.
I want to set up a register and read/write multiple bytes with TWI, but I don't know how...
