Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
We have a setup where our product enumerates as 3 com ports.
Is there a way to name each port from the code so they can be uniquely identified via windows?
The problem...
Hi,
I have MCUboot enabled on my application and would like to enable updating the network core as well as the app core through BLE. The network core is just used for BLE...
Hi,
I am currently developing a project using the nRF52810 as my controller, with SEGGER Embedded Studio (version 5.42a) and SDK version 17.0.2 as my development environment...
TLDR: Turn off your antivirus if you have the same error...
Hi everyone,
I'm trying to install nRF Connect v2.6.0, using either: - VS Code + nRF Connect extension (...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
I have bought an nRF52840 to sniff BLE packets. I have followed the user guide v4.1.x to install all SW on Windows 10 : So far I have downloaded nRF Sniffer for Bluetooth...
Hi,
This might be a simple one, but i cannot figure it out.. How do I place the rx/tx/rts/cts lines from UART0 on a GPIO1 pin?
In the piece of DTS below, 'tx-pin' is on...
nrf Toolchain: 2.7.0 nrf Connect SDK : 2.7.0 Gateway: nrF5340 Audio DK Headset: E arbud 'MOMENTUM TW 4' (Sennheiser) I try to run and test this following application Unicast...
Hi!
In my project i am using a motion sensor that uses a custom protocol. This has resulted in needing to implement bitbanging for it to work. The issue with this is that...
Hi,
I want to obtain the nrf52833‘s’ temperature with the SoftDevice enabled, and I have designed the code with reference to the example project. However, once the temperature...
Hi there,
I am trying to get nRFConnect working in VSCode, but when i click on things in the welcome screen it only shows "activating extensions..." in the bottom bar. I...
1) On p. 55 of nRF52805_PS_v1.4.pdf, section "5.3.8 Reset behavior" shows that a pin reset will reset GPIO, so will a pin reset active low also reset PSELRESET registers,...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
Hi,
I have built and run the MQTT sample for an nRF7002-DK and had it work as expected (connect, publish messages to test.mosquitto.org).
Now I'm trying to get that sample...
