Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
Hi,
I want to identify the specific provisioned node among all n number of provisioned nodes using nRFMesh app.
Does any event will be appeared in sdk, after provisioned...
Hi, I am begginer, I work with SES, Mesh_v5.0.0, nRF5_SDK_17.0.2, and s132, SD v7.2.0. I started it two weaks ago. :)
I tryed the examples, Light switch , with server and...
Does Nordic have an example SW for transmitting and receiving data in BLE 5.2 connectionless isochronous communication mode? Is there a SoftDevice that would support this...
Hi, good morning , i am just wondering is it possible to send and recive data through ble faster than the coded examples please as i am sending gyrodata and its taking about...
Hello - I've google'd around a bit on this unsuccessfully...
I've successfully provisioned and configured an nRF Mesh network with mutliple servers and a single client,...
hi, I am working on the nrf52832 device, I have implemented the push button and I am able to detect button push and release but I want to notify the app when the push button...
Hi,
I am trying to interface nrf52832 with LoRa transceiver module sx1262. Can anyone please provide some sample code to check basic Tx/Rx of this chip. I am unable to find...
Hi,
I am looking for an example that uses the eDMA with the TWI in the 15.2 SDK on nRF52840.
My idea is to read out an external sensor using the TWI with as little processor...
Hi,
I would like to know how to set the service to NB-IOT Cat NB1,
and how then to set the UL subcarrier spacing to 3,75 KHz,
and how to fix the power to 23 dBm, not...
