I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi, I have been studying a lot of issues reported here about leaving network and joining another. The most common answer is to use zb_bdb_reset_via_local_action(0); But when...
Hello,
I am using nRF52833, nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 and SEGGER Embedded Studio for ARM 5.34.
I have imported the ble_zigbee_dynamic_door_lock_nus...
Hello,
I am looking at using the nRF52805 in a new design, but I am worried about the 0201 and 0402 components that are recommended. Currently, my company manufactures our...
Hi,
I am evaluating Zephyr mesh and implemented two timers; one triggers at every 2 mS, the other triggers at every 500 uS.
I put a code in both timers' events to toggle...
Hi, Our platform is NRF-52833 Our project use RS485 bus (nordic's uart + a 485 chip) to communicate with other device. And we choose the libuarte to be the uart handler to...
Hi,
In the nRF_SDK_for_Thread_and_Zigbee_v4.1.0, in examples/thread/NCP/radio folder, there is no option for compiling the firmware for PCA10059.
I want to run RCP firmware...
Hello guys,
I'm trying to interface ds18b20 temperature probe and I'm using this code , In termite its showing output as -0.062500 I don't know why can anyone tell what...
Hello,
I'm using NCS 1.4.99 with a nRF5340DK and want to use the hardware CS of the SPI and also use BLE.
Here is a simple code that work on a nRF5340PDK but only work...
Hi All,
I was just reading the white paper on RF testing guidelines, and I noticed several times there have been mentions of "nRF Performance Instructions" for each of...
Hi,
I am working on NRF52832-based board, with SDK 15.2.
My BLE device is protected with Legacy Connection OOB preshared key.
I would like to use Android NRF Connect...
Hello dear,
I am installing Embedded Studio on OSX (Catalina), and I following the nRF Connect step... all goes fine, but when I try to use "Open nRF Connect SDK Project...
I'm trying to see debugging info with nrf51 dongle.
As far as I can tell I just need to use:
#define NRF_LOG_MODULE_NAME "APP"
#include "nrf_log.h"
#include "nrf_log_ctrl...
On a nRF5340 DK the sample ncs/zephyr/samples/subsys/usb/cdc_acm runs fine. However, if I add "CONFIG_NO_OPTIMIZATIONS=y" to prj.conf I get faults (see below). Any ideas why...
