Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hi
this is not a question - I'd like to give feedback about the peripheral example usbd_hid_generic.
I'm new to 52840 and new to USB. As learning lesson I tried to build...
Hi All
I am now developing BLE application on nRF52840 DK. I have a question about BLE retransmission process.
When master sends a packet to initiate a connection event...
Hello All,
When I was testing our ble keyboard, there was a problem with the Lenovo tablet connection pairing binding. Please help me, thank you!
1. Ble keyboard is based...
Hi,
I need to send data from a CSV file on the nordic board(Via fatfs library). I have presently gotten a Gatt service up and running.
I have a mobile application which...
Hello ,
Do we need to use TIMER1 ,2etc.. to use TIMER1 ? In my current configuration i have set NRFX_TIMER_ENABLED to 1 and others to 0 "NRFX_TIMER0_ENABLED and other instances...
Hello,
I'm trying to use th nRF52832 as a slave SPI device but in the examples "spis" I see the firmware uses DMA.
Can I use it without DMA?
Also, what is the difference...
Hi ,
I need to generate a count data to third party library.
So I create a timer1 ,it can work well.
But I set time_us equal to 1 ,the "timer_led_event_handler" don...
I am interfacing external RTC PCF8563 to nrf52840. Also I will be using low power sleep mode. Will it be possible to wake up nrf using 1hr alarm interrupt of rtc?
Hi ,
I am working on the project based on nrf9160.
Please verify it-
1. I want to print the current clock source of the board as board is initially work on LFCLK....
Hi!
I am feeling a bit stupid, since I know that I must have made a config error somewhere. I just don't know where. I am developing a BLE HID device using SDK 16.0 and...
Hello,
I have trouble with interrupt.
I use pin 16 to trigger interrupt signals from a sx1261 module.
It has worked well on example code with SDK 14, but for my projet...
SDK Version: 15.1 IDE: Keil Softdevice: S132 v6 Example: Blinky peripheral example slightly modified Q1. Does the Softdevice use RTC0? Q2. Does the App Timer use RTC1? If...
Hello everyone,
I am using the pc-be-driver-py library to start a scanning with IRK and I view the advertising events that I get. My peripheral is configured to do 1 advertising...
