I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. It is placed on a custom board such that all pins from the nrf52 SoC are brought...
Hi,
My projects with Nordic chips thus far have been pretty simple, but now I would like to use an RTOS. My question is, do I use the FreeRTOS available in nRF SDK, or move...
Hi,
I have a problem with understanding, how bits in ble_gatt_char_props_t are related with Specification of the Bluetooth System v5.1 Table 3.5: Characteristic Properties...
If I use a breakaway for some debug pads which SWDIO and SWDCLK are connected to and then snap it off so the traces are no longer connected to anything, will this cause a...
I'm trying to run the https://github.com/NordicPlayground/nRF52-ble-long-range-demo on Fanstel modules with integrated AFE by Skyworks - BT840X(E) https://www.fanstel.com...
I'm trying to connect to an AWS MQTT broker I have set up based on the code in https://github.com/joakimtoe/fw-nrfconnect-nrf/tree/36532a8ca60bf7139a988b5cbb4e6cb47948a9fa...
Hello In this thread we discussed a possability of building a system with large number of conecctions. So, we need to get data from 30 peripheral nodes on one central host...
Hi,
I'm developing a product that should take an image of a low-resolution image sensor, process it and send the result via BLE.
The camera has an 8-bit parallel interface...
Hello, I was finally able to connect the board via LTE to my nRFCloud account. However, when I go through the getting started guide, specifically the programming a sample...
Hi
Now I use the SDK15.2+MESH3.10 build my project.
Because my firmware was very large.
Moreover I want to use the nRF Connect update my device.
So,how to integrating...
HI I started off to test all the drivers before the actual development process kickstarts.I tried using the TWI sensor example for an i2c driver check.I used a DS1307 simple...
Hi,
I'm trying to add an interrupt triggered event to my code (which is based on the experimental LPN example from the Mesh SDK).
Looking through the development zone...
Hello , I come from taiwan.
I am using ble_app_hrs_c to connect my heart rate watch
I can set m_target_periph_name to search for devices with the same name and connect...
Hi, I'm developing a project on nRF52832 with LIS3DH accelerometer . Is there anyone here who has already done a similar project using the nordic SPI bus (not TWI)? Please...
Hello NordicSemi,
Actually we want to develop a product that can communicate with the iPhone over USB (lightening connector).
Basically want to implement iAP2 protocol...
