I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
As in the title, I installed 64bit nRFgostudio, however it crashes just after opening with the log below. It opens fine when I do not have my Thunderbolt 3 docking station...
Hi,
How can I send message from servers other than 0x105 and 0x106 to client?
I receive status message in client from servers 0x105 and 0x106.
I can send message to...
I'm trying to use the SDK 15.0 saadc example with a potentiometer on AIN0, and I'm getting weird values. Left pot pin connected to VDD, right pot pin to GND, center pin to...
Hi Nordic:
I want to add some rtt log in the bootloader code, so I make bootloader flash start at 0x77000, size is 0x7000, and my application's FLASH_PH_SIZE is 0x77000...
Hello, I read in the documentation how to create a model, in the client model, which defines a struct: simple_on_off_msg_set_t {uint8_t on_off, uint8_t tid}. I do not understand...
See: http://www.keil.com/forum/63929/
Everything here refers to J-Link, eg devzone.nordicsemi.com/.../a-working-demo-of-monitor-mode-debug-mmd-on-sdk-15-please
and Google...
Hello,
I am wondering that what exactly are the differences between libmbedcrypto.a and libmbedcrypto-software.a?
I read through the SDK documentation about the opethread...
In SDK 15.2 in ble_gap.h
#define BLE_GAP_SCAN_WINDOW_MAX 0xFFFF /**< Maximum Scan window in 625 us units, i.e. 40,959.375 s. */
#define BLE_GAP_SCAN_INTERVAL_MAX 0xFFFF...
Hi Everyone,
I'm using nrfutil in an arm cortex a8 running Debian 9 with kernel 4.14.49. The processor is connected to a NRF52 dongle through USB. I'm trying to flash (using...
Hello ! My custom board is working fine (with the last programm I flashed into), but I can't access it with my debugger and I can't flash it again. When I try to flash it...
This is my Output, Looks good but not working/
Preparing target for download Executing script TargetInterface.resetAndStop() Reset: Halt core after reset via DEMCR.VC_CORERESET...
I am using nrf52832 with latest version of s140 softdevice.
I migrated a project, that was used on a nrf51 chip, to the latest sdk version.
The problem is that the measured...
The zipped project attached to this blog doesn't say what SDK version it should work with - but it certainly doesn't work with v15.
https://devzone.nordicsemi.com/b/blog...
Good afternoon,
I have a question regarding the ble_app_hrs_rscs_relay example. I am using this example to read scan response data from a peripheral without pairing with...
