Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi.
I'm busy to add the nrf8001 BLE module to my PIC32MM product for negative pressure monitoring in a small area. Is there is list of minimum settings that is available...
Hello,
I'm having issues with the advertising module in SDK 15.0. I basically want the device to fast advertise for 3 minutes and then switch to slow advertising forever...
When I configured POWER_CONFIG_DEFAULT_DCDCEN =1, I found almost no change compared to the case of dcdc, but when I added APP_ERROR_CHECK(sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Quite a generic FreeRTOS question probably here but... on an interrupt, what's the stack the ISR uses? Is it the one from the stack that got interrupted? If so, I guess that...
HI!
I'm using two nRF52840 boards to communicate using ESB. The ESB API doesn't have a pairing protocol so I figured I'd write one without encryption or any bells and...
Hi all,
when I insert ble_nus into mesh_gatt . I realized there are two pulse functions with the same function:
and
if they let them coexist , when I use nrf_connect...
Hi
Using the iOS 'nrf Mesh' application I can provision a PCA10056 succesfully.
I have written fimware image that sniffs for mesh related becaons, and when I power up...
I want advertise data only change with uuid for every 100ms I gone through the nrf 51power consumption guide I guess its same for nrf52 any help for changes or must have points...
Hi,
I'm using multilink Central device with SDK9.0 and stack S130. I'm able to connect to multilink peripheral device as expected. But i am not able to connect to a Custom...
Hi, is it possible to check the current configuration of a GPIO pin? I mean if the pin is currently configured as input or output. Next I need to uninitialize it and reinitialize...
Hi,
the Nordic nRF-series SoCs have got the restriction, that the power has to rise from 0 V to 1.7 V in 60 ms for a guaranteed POR. In our application we cannot guarantee...
We use nRF52832 on our product. We need to update the application remotely in the field using smartphone with BT. The unit in the field will already have an app running on...
Hi,
I'm working on treating the nrf as a CDC ACM device and in order to test it I've been using a script to send input to the chip through echo commands to the /dev/ttyACM...
Hey, can you say me, how can I switch on of the Node-Features (relay, proxy, friend) with help of the Interactive mesh provisioning and configuration Script pyACI.
