Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Development board: nRF54L15DK i I'm already using "Find My Example" to connect to the "Find My" app on my iPhone. At the same time, I also want to connect to nRF Connect....
Hi,
there is my project rom size in memory report , I would like to asking what is the "NO Paths" item and hidden item
they hold my 20% ROM size. and what is the content...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hello,
I am trying to modify peripheral_hids_keyboard 's security configuration as Security Mode 1 Level 2.
According to some Q&A thread, I tried the following:
1...
hi support team,
may i ask how to set static ip address for 7002?
1. i set these configs:
CONFIG_NET_CONFIG_SETTINGS =y
CONFIG_NET_CONFIG_NEED_IPV4 =y
CONFIG_NET_DHCPV4...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
