Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to send images to my arduino from an app to nrf8001 and then display it on my device. Is nrf8001 made to only work in 20-byte wide receive buffer? Can it receive more...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hello all,
after a long period of trial and error I come for advice. I use the NRF24L01+ module with a slightly modified NRF24-library based on the work of MikeM ( www...
Hello,
I've recently bought a nRF905 development kit. From the nDP soft, i cannot detect my nrf905 EVBOARD.
The following driver is installed : "nRF2401 FS USB DEMO...
Good morning,
I just finished my circuit with nrf8001 + balun/antenna.
What is the process to have it review by Nordic?
Sorry for this question, I'm pretty new to PCB...
Hi
I would like to develop an application for the nrf51822 with a static passkey that connects with linux. The example "nRF51-ble-app-uart-static-passkey" gives a great...
Hi,
I would like to use Random number generator when soft device enabled. I have seen random generator example, but I can not use the same when soft device is enabled....
I was considering the following possibility, using an nrf51882 module or another module to receive ble advertisements. I'm pretty sure this is possible. Using the internel...
please, help me ㅠ_ㅠ
it mades me crazy
My PC is Windows 8.1 & 64 bit.
I try to install / repair / change SDK (6.1.0 version, 6.0.0 version, 4.4.1 version)...
I have achieved the demo referring to the IoT SDK and can control the lights on the nRF51 DK through the Firefox browser with Copper plgu-in in the LAN.Recently I want to...
Hi,
I interested in a simple system of a master and slave nrf2460. But how many of these systems would happily coexist in a the same room?
Thanks
Senthil
The Enhanced ShockBurst PTX Project just inits the ESB and start transmitting without ever configing either of the 16MHz or 32kHz clocks (none that I can see at least).
...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
hi.I have a question about synchronization. In main loop, there is a function sd_app_event_wait() which blocks until ble event from softdevice call occurs, so I want to put...
