hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
To the kind attention of Nordic support team,
We are doing EMC pre-tests of our products using your nRF52833 .
At this stage, nRF52833 device is triggering itself a...
Hello.
I am following this tutorial, but unfortunately I am stuck at step 7. I am not sure which characteristic corresponds to the UART RX characteristic value.
I tried...
I've started an asset tracking project at the company that I work at and have tried to use the nrf9160 dev kit for the device tracking part.
I have updated the board firmware...
Hello -
We are working with the nRF52840 and SDK v17.0.0 and tuning our power consumption during System ON sleep. We understand how to wakeup the device using the RTC and...
Hi,
I have encounter a problem that the first button release event is missing if the key is pressed while powering up.
The SDK I am using is nRF5_SDK_17.0.0_9d13099. ...
Hi!
We are using nRF52832-QFAB (B0 variant) in one of our projects, and it works fine and well.
We are now in the process of using the nRF52832-QFAB-E0 in the same build...
how can I work it use nRF5 SDK 17.0.0? On https://developer.nordicsemi.com/nRF5_SDK/pieces/nRF_DeviceFamilyPack/ the newest pack is
NordicSemiconductor.nRF_DeviceFamilyPack...
Hi Support Team,
An error occurs when generating a signed binary file for central_dfu_smp.
Error: Header padding was not requested and image does not start with zeros...
Hello everyone
I success in compilation gpio basic example but I have some problem about bluetooth mesh example.
It show message "undefined reference to `bt_rpmsg_platform_init...
Hello!
I've only used the DK board so far, so I've rarely used an external debugger.
I'm going to use a custom board later, so I'd like to learn more about how to use...
I just both the board, and I can get the 4 LEDs and the NFC to work; I have followed all the instructions but unsure what is going on - and suggestions?
1.nrf9160 module abnormal reset, no abnormal reset log information, I would like to get modem related log submitted to you for further analysis, but I do not know how to use...
I use nrf5_SDK_for_Mesh_v420 on four nRF52 DK board, one is client, the other is server. But I fond, the light_switch_client example is used to control two server board, now...
Hello,
I am using the Light switch example for BLE meshing. I am trying to provision the nRF52832 with Raspberry Pi. I am unable to successfully provision because of the...
Hello!
I have created a function that cancels the connection by pressing and holding the button when Bluetooth is connected.
The use of this code allows the connection...
