Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I am following Getting Started Assistant on Mac platform.
However, I run into an error when I issue: " pip3 install --user -r zephyr/scripts/requirements.txt ".
" ERROR...
Hello,
there’s a section in the NRF9160 specification (11.1) that calls out that VDD_GPIO should be applied after VDD has been applied on power up and VDD_GPIO should be...
Hi,
I am sending firmware image using my DFU master. The image needs to be divided into data objects each of 4096 bytes and then those again into 244 byte BLE packets. So...
Hello,
I'm trying to connect to nrf connect with the nrf9160 DK. I am using an Irish vodafone NB-IOT sim to establish the connection. This sim has an access control list...
Hi,
I have a question regarding a DFU update via BLE. I am using mesh sdk v3.20 and sdk v15.30 with custom hardware (nrf52840).
I have the BLE DFU working as expected...
Hi all,
I am using mesh sdk3.20 and sdk15.30.
I noticed that with the buttonless ble dfu, it is not possible to perform a DFU transfer after the device was provisioned...
I did the program using examples of glucose. But I do not want to enter passkey from central. Because there is no LCD or UART in my device. Which part of the glucose example...
I am developing firmware for my Peripheral Device (nRF52840) using S140 (v7) and SDK 15.3. In my application, I will advertise (with advert payload changes) and support Smartphone...
Hi,
How much is the expected time period from the time VDD goes above 1.75V to main()? I am using a custom bootloader and am seeing a ~4.5s (yes seconds!) delay in getting...
i'm trying to configure the nrf to rx and according to the state diagram i realized that: as the nrf is supplied and the voltage goes over 1,9V the nrf goes in the power down...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
Hi, i'm using the nrf24l01 with a zynq board to use it as radiocontrol; i'm trying to configure the nrf as receiver so that i'm able to send data from another nrf connected...
I am trying to use the LPCOMP API, but I am having trouble with the following function:
nrfx_err_t nrfx_lpcomp_init
(
nrfx_lpcomp_config_t const *
p_config ...
I'm attempting to setup GPIOTE for an output that is set and cleared by different events. The GPIOTE driver doesn't let me initialize an output twice. Is there a way to do...
I have 2 objectives BT beacon and concurrent ESB with Thread using time slotting A. I would like my thread devices to broadcast BT beacons. As this does not require any reception...
