As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,I have some problems when disable peer manage in ble_app_buttonless_dfu project in sdk15.3.0 on nrf52810.
I disable PEER_MANAGER_ENABLED in config.h and remove the peer...
I want to save encryption state in DFU to the nrf_dfu_settings_t structure. I put a new 16-byte field at the end of the structure after nrf_dfu_adv_name_t adv_name; and whenever...
Hi,
I am specifically looking for RSSI implementation using the BLE module on nrf52840 SOC. How to obtain the RSSI values for asset tracker application on Nordic Thingy...
I'm designing a board using nRF9160 with eSIM. But according to the eSIM specifications (chip spec), the current consumption is <[email protected]. Is this continuous current consumption...
hi,
i am working on multilink. currently i connecting to 8 boards.
// <o> NRF_SDH_BLE_PERIPHERAL_LINK_COUNT - Maximum number of peripheral links. #ifndef NRF_SDH_BLE_PERIPHERAL_LINK_COUNT...
Hello,
I am using dynastream module with nrf52832. I programmed the ant module with s332 hex file and the example of ant_io_tx of s212 arm5_no_pack as below,
Im...
Hi Dears,
I have submit a issue for about two weeks but no response yet, would you please help me for handling it?
The link is https://devzone.nordicsemi.com/f/nordic...
Hello,
I am working on nRF51822, SDK12.3.0 in IAR workbench.
I am use init pin 2 as an interrupt.
Device will advertise for 20 minute after 20 minute device go to sleep...
Platform info: SDK153, MESH 3.2 and using SEGGER RTT for debug logging output with __LOG(...)
I have a strange behaviour in one of my application, where it work very fine...
Hi,
I am using nrf52 Bluetooth to transfer the data .Here i am not getting how to transfer the data at 10ms through Bluetooth.
Is there any example program to transfer...
Hi,
I'm evaluating a custom PCB that uses the MDBT50Q (nRF52840) and I'm really stuck. It looks like the device is working, but I'm getting a few strange issues.
Out of...
Dear,
we are developing a beacon product with nRF52832 powered from Li-SOCL2 primary battery. I understood that We cannot connect directly battery to the nRF52832 beacause...
Hi,
Anybody managed to connect a WisNode RAK811 to an nRF52840-DK and make them "talk" ? (send "at" commands to the RAK811 shield and get replies)
How did you connect...
Hello Nordic Community,
I am using latest firmware mfw_v1.0.1 latest NCS tag (v1.0.0) as well. I flashed GPS example into DK successfully. I made custom hardware using nRF9160...
