Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
I am a beginner in the study of Bluetooth, and I have difficulty in understanding the purpose of API functions Bluetooth stack. For a better understanding of the system API...
I'm using MCP 3.1 and tried flashing the dongle from it multiple times. I also tried reinstalling MCP, but to no avail. When I flash some Blinky example using mbed it works...
I want to read whole flash memory using for loop and see how long it takes. What i have noticed is that it does not print all the lines. On the other side i ask myself: Does...
Hi,
I am very new to nRF51822 controller. i got some problem with compilation.
i have downloaded SDK v10.0xx and tried to compile blink example from following path.
...
Using Segger Embedded Studio 310i in Linux and SDK12.2.0, I imported the Beacon example project (ble_peripheral/ble_app_beacon) from Keil. Right now I'm trying to make it...
Hello everybody,
RTC0 is used by the SoftDevice. Is it possible to use the current RTC0 counter value as a system time, so that RTC1 doesn't have to run additionally? For...
I created a service with several characteristic values. I can read the values without any problem with the Master Control Panel on my Android tablet, but reading from the...
I am working with nrf51, SDK 11, S130, Keil uVision 5 and have an Application with RTX and want to use DFU OTA.
The bootloader works with the app_hrs_dfu example.
When...
Hi, I tried to enable non-connectable advertising timeout using the macro APP_CFG_NON_CONN_ADV_TIMEOUT in es_app_config.h, but it has no effect. I test this using nRF connect...
Hello,
When I call TASK_START in SPI Master it does not start a transfer. According to registers all seems to be set.
I found what was the problem. When I called TASKS_SUSPEND...
I am using SDk 11. S130 V2.0
What is the equivalent of spi_master_evt_handler_reg ?
I just want to configure my handler to receive the interrupt of the SPI master.
Please...
Hello, I've just purchased nRF52 dev kit and I'm using ble_app_uart example from SDK_12.2 to send/receive data from one pc (which is connected to the dev kit through usb)...
I have been trying to use nRF5 SDK 12 on nRF52 Preview DK by using PCA10040 instead of the removed PCA10036. But example 'ble_app_hrs' that uses SoftDevice S132 v3.0 do not...
Hello,
I am developing a custom board using nRF52. In my previous custom board, the total current consumption is 15mA with DCDC regulator enabled. I want to reduce this...
