Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi, we are using NPM1300 with a ICP401835TPRT renata battery. It has a 10k B=3380 NTC (part number NCP15XH103F03RC ). I'm getting a really high temperature reads and very...
Hi,
I am trying to optimize a time critical device for lowest possible latency data transmission over BLE on nRF5340 working as peripheral. Currently my algorithms are implemented...
I'm adding MCUboot to my application and we'll be using our own app to upload new firmware over BLE to the device over our custom comms protocol. I can use the DFU Target...
Working on a nrf5340 project, and running into limits of the size of the flash to store my application image along with mcuboot bootloader.
I had a mucboot setup that fitted...
I have a modified asset_tracker_v2 running with SDK 2.5.0. It is connecting to AWS and sending data perfectly. It has been running for several years without a problem. I am...
Hello,
I’m running the AWS IoT sample on nRF9160DK v1.1.3 using nrf-sdk and toolchain v2.9.0, modem v1.3.7.
Everything works fine when following the instructions with...
Hello community, I am currently looking for a solution outside the 2.4 GHz band and I came across NR+. Does it suit my needs for M2M (Machine to Machine) communication? If...
Dear Nordic experts,
My question is simple, how to get the 6 octets default MAC address by app SW in nRF52840. The question was already raised by someone some years ago...
I have an issue when trying to install nRF Connect SDK on my work computer. I have installed VScode, the toolchain and the nRF Connect extension. The next step would be to...
I have been trying without success to install either the v2.7.0 or v2.8.0 SDK onto my Windows 10 System. Every time/method I've used results in an error equivalent to
...
Hi,
SDK17, Softdevice S112, NRF52805 custom board.
I have baremetal bsp implemented but I am new to Softdevice and struggling a bit with an interface concept beween two...
Hey,
I'm using the nRF5340 and want to run the PTS test with the following configuration: The CAP initiator establishes two audio streams within a single connection to the...
Hello,
We are currently experiencing some unusual behaviour on our feather board (circuit dojo, nRF9160 chip) which we are seeking advice on.
Whats happening:
Device...
Hello,
I'm using NRFX PWM directly because I need something more custom than zephyr's PWM driver provides. I'm trying to understand what .pin_polarity field in the config...
Hello,
When I follow the steps to create a new standalone workspace application for SDK and Toolchain 2.9.0, and then add a new build configuration and build the project...
