As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
I'm developing an accurate and low drift millisecond-resolution timer on the NRF52. I'm limited to the resources on the NRF52 itself. Details of the system:
Initialise...
Is there anything special required to make a n52832 work the very first time the chip is programmed? Fuses to set, etc?
I'm new to nordic chips and I was handed a board...
While creating a DFU bootloader based on the bootloader_secure_ble example, I was having trouble getting a device to boot into DFU mode.
Initially the device would get...
(Sorry for the formatting. I don't know what's going on with it--the preview looks ok!)
I'm creating an application that uses
a modified version of the ble_nus
example...
Hello guys,
I have problem, I activate the BLE and connect it to my tablet application until then nothing wrong happens. But when I use sd_ble_gap_disconnect() to disconnect...
I plugged my nRF52 evaluation board to PC using a micro USB cable, dragged a ble_peripheral hex file from Nordic examples to the mounted JLINK drive, started up nRF Connect...
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12....
In nrf51422, what is the behavior of these registers when an external rail-to-rail clock source is applied?
Do I have to issue HFCLKSTART? If
not needed, does issuing...
Hi,
I am testing the light_switch demo of the nrf5_SDK_for_Mesh_v0.10.1-Alpha_src.
I don't have 32kHz osc on my server board, so I have to change the clk config. I config...
Hello, guys,
We have developed our first generation product with 51822(16KB RAM, SDK10, S110V8.0) as peripheral , and we are always facing the problem that the connection...
hi
I am using peer manager to pair and bond android phone to nrf52840. I want to give custom peer id to this phone during bonding process, then if i lost this phone i will...
Hello,
I am sending a float in my BLE payload, using nRF Connect I can sniff and see that the value is being sending, it changes every time.
However, in my central when...
Hello Nordic community,
First of all would like to say that I am aware that BLE protocol allows to send only up to 20 bytes size packets. Moreover, I understand that I...
