I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi I am testing the Thread examples
I worked on SIMPLE_COAP_EXAMPLE in nrf52840 DK there it works fine while opening UART and enter to CLI commands and its working
but...
Hi again Nordic. I'm trying to write sensor data to the external flash continuously as there is not enough RAM to hold all the data required. However, the writing operation...
Hi,
I am using BL653 dvk to write an application for SPI, In my prj.conf, I added below parameters:
Now when I am debugging SPI master code, execution enters the file...
We are performing a preliminary power analysis with this device and have questions regarding the power consumption reported in the Product Specification. For example, the...
I've been struggling with enabling HTTP support on the serial_lte_modem. I've tried using various versions, currently I'm using NCS 1.8.99. I edit the prj.cnf to include CONFIG_SLM_HTTPC...
Hi,
I use nRF52840 and SoftDevice s140 (7.2.0). I use SEGGER Embedded Studio to compile a project written in C++. But lately I've been having trouble debugging. For example...
i've been test code from nrf51-app-button-example/main.c at master · NordicPlayground/nrf51-app-button-example (github.com) but not effect when presss any button.
I am new to Zephyr and Nordic. I onserved that to use variuos APIs it is required to declare in prj.conf file. But, where is the list and document of various commands woth...
Hi
I have a Nordic nRF51 as a Peripheral.
I have it open advertising until it connects for the first time to an Android handset.
When a connection is made it stays...
When I switch to any branch other than 1.8.0-rc2, I get the following notification:
"This workspace requires version 1.8.0-rc2 of the nRF Connect SDK, but it isn't installed...
I am developing a BLE Peripheral device using the nRF52805 and have just discovered that neither of the two SoftDevice packages offered for this chip have support for extended...
After compiling an example and attempting to connect to my board, VS Code won't connect to my board. It is definitely recognized by my computer, and the Programmer application...
Hello everyone,
currently I am working on my application which is based on the multirole example and with the SDK17.1. My target is if one device connected to another the...
what is the external 32.768khz crystal tolerance range for BLE? we have a product, it easily disconnect with another one when the distance is 5m, the PPM is -120ppm, fine...
Hi,
The project is a multi-link environment of nrf52840, The 7 peripherals has the task of send data constantly of a sensors. All is working on coded_s8.
The objective...
