Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Hi There.
I just downloaded a SDK for the wisol module that uses the nRF52832 and i can't get it to compile in Keil V5.31. Im getting this error:
Error: *** Project...
Hi
I am new on nRF52833 and want to try RF test for development.
I have a nRF52833_DK on hand with Direct Test(DTM) in nRF Connect(Descktop). However I am not success...
Dear Sir/Madam,
We are «SMART Solutions», Ltd. a startup from Tomsk, Russia.
Our company developed iBack Posture Corrector please see http://en.iback.online/ .
The device...
Hi Nordic team
I tested the example [802_15_4\wireless_uart\raw\first ] period 1s send 20 Byte data to example[ \802_15_4\wireless_uart\raw\second ]serial tool to printf...
Hi
I am working on a project based on Thingy91. Is there any sample application in NCS SDK to show the communication between the two SoCs on the Thiny91. I will need to...
Hi all,
I migrated my nRF52840 examples from SDK 15.2 to SDK 15.3 folder and when I tried to build
the examples and I discovered that nrfx_power_clock.c could not be found...
Hi
I am working on the Connectivity Bridge project using Thingy91. I noticed that the Thingy91 shows up as a USB drive that has four utility files, readme.txt, config.txt...
I am trying to hook openthread with freeRTOS.
Short story: the current state of my implementation is that I get a hardfault after succesfully calling mqttsn_client_search_gateway...
Hello,
I've added quite a few interfaces and endpoint configurations and I'm trying to figure out how to properly respond to "Get Descriptor" Setup packet that requires...
Hi, I am using nrf5832 sdk 14.2 where I am trying to scan the data and advertise same data with some modifications. I have used Central and Peripheral example ble_app_hrs_rscs_relay...
Hello,
I am trying to compile the samples from SDK_for_mesh_v4.2.0 but i have problem with my environment set-up. I am following closely the documentation but I think something...
Hi everyone,
We have three ADC channels, two of them are implemented as a simple ADC without oversampling, the third one uses oversampling. Because one of them use oversampling...
Hi, I have started development on nrf52840DK . 1-I have installed nrf Connect SDK v1.3.0.
2- I have also installed Segger Embedded Studio Nordic Edition. and selected nrf...
Hello, Please help i m trying to share memory between Network and App Cores in a nrf5340
How To do?
at page 21 Figure 2 Memory Map
it seems that FLASH address 0x0000...
Dear Sir.
Some problem with the PWM .
Pwm output on pin 12 is connected to a buzzer.
When pwm_pin_set_usec(pwm_dev,PWM_IO, 260, 130,0) is set through the pwm_init...
