Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hello,
I have followed all the Getting Started documents to setup the development for my new nRF9160 DK.
Among them, I installed SAGGER Embedded Studio version 4.52
...
I have as starting point the HRS FreeRTOS app. Now I want to add a millisecond counter. But from what I read I'm a little bit confused. Can someone tell me what's the best...
Hello, I am working on a custom NRF9160 and I am on SDK 1.3.0. I am working on the asset_tracker project and I want to put my own accelerometer there. To do this, I changed...
Hello,
I have been using Nordic mqttsn examples (publisher/subscriber) along with an OperThread Border Router. So far I haven't changed the parameters of the Thread Network...
Hi,
I am trying to adapt the read register function that use the TwoWire lib of Arduino in order to read a Sensor Hub Response Byte of a defined Host Command :
to...
Hi
The flash data retention time for nRF52832 have been specified for 10 years @ 40°C. Is there any data available what the retention time would be at higher temperatures...
We are developing tracking system for our ground floor car parking but couldn't able to get GPS location.. we install Nordic Thingy:91 inside the steel body. Please let us...
Hello guys,
We are developing nRF52840-based device that needs to act as both BLE Central and Peripheral.
Peripheral role:
In BLE Peripheral mode, nRF52840 should advertise...
I have a need to send pressure data form 1 device to 4 other devices , it is medical application , data rate is in such a way to be in human readable form, can i use nrf24l01...
Hello, Just purchased a nordic NRF5340 PDK from digikey. On plugging the micro USB 2.0 and switching on the device , the device powers up for couple of seconds (LED1 & LED5...
I'm trying to add BLE_UART functionality to a custom board, on top of the already existing USB (and working) USB_CDC CLI. I'm using SDK 15.3.0 and softdevice S340
I used...
Hey
I would like know how can i add battery model for mesh. I have seen the Battery indicator in normal BLE sdk, now I want to implement in mesh sdk in the form of model...
I'm currently using a HostController with pregiven communication protocol for transfering data to the NRF52840 (over uart). The NRF is flashed with the SD140 and I'm using...
Hi Dev Zone Team,
I had a question regarding the current measurement of Nordic Thingy 91. I am following the steps provided in the Thingy91 documentation.
I have a Joulescope...
Hello.
I am testing saadc function.
When I was connect the saadc pin with ground level, the saadc value represents negative value.
So I am searching the similar problem...
