I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi, I am testing the PaWR examples in the NCS and I have few doubts.
In this page , it says in section 1.3 that there are two ways for synchronization - PAST after connection...
From what I can see in the documentation, UART0 is used by default for "non-secure" / application logs and UART1 is used for "secure" app logs. I am needing to interface with...
Hello, I am using an I2S PDM Mic and trying to send the I2S Data over BLE using Segger Embedded Studio. The I2S Program that I have generated is working ok. I have verified...
I am using SDK 2.9.1. I wanted to follow this tutorial:
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-7-device-driver-model/topic/exercise...
Hello Nordic friends,
currently I use NRF7002-EK successfully in my bare-metal environment, but for debugging, I'm considering using the EB instead of the EK if the edge...
Hi All,
I am currently exploring on nrff4l15 SOC and have its dev kit.
I read on this forum ( multiple tickets ), that there is a support of NSIB. I would like to know...
Hello, I have an application running on an nRF9160. The current app was built using NCS 1.7.0 with the L2M2M Carrier Library enabled. I'm upgrading the application to use...
Hello,
We are developing a Cellular IoT device based on nRF9160 SiP. Essentially it is a battery powered temperature and humiduty sensor, that sends the measurement data...
Hello everyone,
we have an in-house HW with the nPM1300. Both load switches are configured as LDOs as described in datasheet chapter 9.3 configuration 1.
LDO1 is used...
Hi,
I have successfully implement the BLE video transfer using nrf70-wifi-ble-image-transfer-demo .
I can receive the image using the Android-Image-Transfer-Demo application...
I am using VSCode with SDK 2.9.1. I have added the spi21 to the device tree UI editor. When I choose the MOSI, MISO and SCLK, they all show up in the visual representation...
1. Our system is configured with circuit config3 of the nRF52833 WLCSP, where an external power supply of 1.8V is applied to VDD.
Power sequence : USB connection -> VBUS...
Hello,
I'm using the SLM application with an NRF9160. I'm sending AT commands for MQTT publish. After ~10hours the device reboots.
The setup AT commands from powerup...
Zephyr Version 3.7.99, Zeyphr SDK v0.17.0
Thread Version v1.4
Matter SDK Version 1.4
After the switch from Matter SDK version 1.3 to 1.4, the NVS module under Zephyr...
