Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hello,
I programmed about 200 nrf51822 boards for prototype production.
The order was softdevice - bootloader - application.
In the process of test I saw some abnormal...
I'm a bit confused about nomenclature and am looking for guidance in how best to implement the needs of my ble app. From the S110 perspective, how are connecting, bonding...
Hi there!
I'm working with secure_bootloader example (SDK 12.1.0) and trying to use i2c communication on bootloader. I'm using the debug code and checking via LOG (uart...
I have built a application with IAR, and made a hex file with Intel extended. It’s works fine with nRFgo Studio. But I got problems with dfu updating from my android. I hope...
Hi. I would like to convert float32_t to uint8_t array for transmission using the ble_nus_string_send function. Can you guys please suggest the method to convert the same...
Hi
To write the some state of the device, I write two bits into the NVM memory. Thus, we get 16 write cycles to one address without erasing. I did this based on the optimization...
Hi all:
I wrote a code to directly read the register 0x43 (MPU_REG_GYRO_XOUT_H)
But the GYRO data I got is wrong
Chip: nRF51422
Board: PCA10028
Firmware: S130_nRF51_2...
Hi,
I am trying to implement a Single Bank DFU over Bluetooth for my nRF51822 (256KB / 16KB RAM) using SDK v7.1 and Softdevice 110. I am using GCC to compile the bootloader...
Hi all,
I my application I am interfacing SD card with nrf52 using FATFS file system. I am observing some weird behavior while doing this. I have two SD cards, one of 2GB...
Hi. i'm using nRF52832, SDK13, S132v4 as multi-link peripheral.
As I know, SDK13 supports multi-link peripheral refering to example "experimental_ble_app_multiperipheral...
Hi,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
Actually, I have used nRFgo Studio to flash the softdevice...
Hi
I'm setting up a firmware based on the DTM example to perform certification tests.
In the DTM example firmware I see that there is a VENDOR_SPECIFIC command option...
hi,
i tried nrf51822_beacon_app.hex( C:\Nordic Semiconductor\nRF51822 Beacon v1.1.1\Source Code\nrf51_beacon\ble_app_beacon\pca20006\s110\arm_build\ ).in that we changed...
This might not be the correct place/forum to ask this question.
Since a couple of days, I am not able to step or next with gdb .
I understand that gdb needs to know what...
Hi：
Now keil4 default is to use the 16_bit THUMB instruction set, if I want to set it to start the program using the 32_bit ARM instruction set, how should we do? thanks
