Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
I'm using FDS in SDK 11.0.0 on a nRF52832. I was having some trouble with freeing flash storage and after doing some research I came across this post and I applied this patch...
Hello,
There is a bug in pstorage.c from SDK which can cause that module to fail to complete a flash operation. The problem is that the pstorage_sys_evt_handler function...
The product spec says "This event will also be generated if the supply voltage is already below VPOF at the time the POF is enabled" but it seems like the event is not generated...
I have a BLE device that is using Nordic SDK 8.1 and uses PWM to control an LED. Now I want to turn the led off with PWM. To do this I set the duty cycle to 0 and printed...
Hi,
I'm working on nrf51822 with soft device s130. I'm trying to send a data packets from the nRF51822 over BLE to an android device.
I want to know how much data...
Hi!
I try to create a custom service. To do that I copied the ble_bas service and followed this guide.
You can see my init function here:
#define APP_UUID {{ 0xC0...
Hi. I'm using nRF51822AC, SDK12.2.0, S130 as central and peripheral.
Q1. What's "sd_ble_uuid_vs_add" function? is it for setting service UUID?
Q2. If Q1 yes, how to change...
I was reading a review of this product from a 3th party and they was claiming that a disadvantage about using this chip is that "Some peripherals and resources are not available...
SDK: 13.0.0.0-1.alpha
example ： ble_app_hrs_freertos
I am developing a product, referring to the “ble_app_hrs_freertos” example, when I tested my functions found a serious...
I've just tried to update the mbed firmware on an nRF52-DK to version 0219, and have hit some problems. Firstly, after dragging the .bin file into the Bootloader drive, my...
I've had a sequene of problems attempting to install the power profiler software on my Lenovo T420 Win7 64 bit machine.
First Issue
When attempting to run the python_packages...
I would like to pick up audio signal with a microphone for ex. AKU340, then use audio codec to digitize it, then save the output in a SD card connected to the nrf52, reading...
Hi there! I am a beginner of bluetooth technology.
We try to build a kind of IoT based on bluetooth mesh nodes with nRF51822. According to the instruction of nRF Connect...
I've found out that softdevice S130 cannot handle the length longer than default MTU(23).
But I know L2CAP is responsible for assembling and disassembling packet.
So...
I'm using nrf51822 & S130 to read the temperature humidity values every 5 seconds from AM2301 sensor. For that I am using timer in system on sleep mode. The current consumption...
