dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I was able to measure current with the test probes I have. However, I really liked the idea of test probes that were like the ones in the drawing below. I have not seen test...
I am using the PWM library in this repository for a nRF51822. I write the following code to generate a ~ 30% dutycycle 500 kHz PWM output:
#define V_CLK 5
static void...
Hello,
I am using Timer_2 with two CC registers configured, 2 PPI channels (one for each CC register in the timer), and one GPTIO_TE to make a PWM to control dimming on...
hi,
my nrf51822dk was downloaded s110 hrs demo,and it was advertising,i used a ble sniffer dongle to get the advertising data.the AdvData is "0B 09 4E 6F 72 64 69 63 5F 48...
Why is it a standard in nordic-supplied code to initialize structs with memset like so? An example would be:
ble_gatts_char_md_t char_md;
memset(&char_md, 0, sizeof(char_md...
//Edit:
So Hung Bui just told me in another question, that there is indeed a buffer of size 6 or so?
How can I decrease that to 1 (i.e. disable it) so that only the latest...
I have the nRF52 DK and cannot determine the silicon revision on it. Is it the 'Engineering A' revision and therefore is subject to all the Errata that is currently published...
there are 3 modules to test(A1,B1,C1)
*2. A1 connect with B1(B1 is master, A1 is slave), C1 is power off, B1 as slave attempt to connect C1 with BLE_GAP_ADV_TYPE_ADV_IND...
I need a PWM signal as outoput from the nRF51-DK. And I do need the softdevice. So I decided to pick the code from the nrf51-pwm-library-master and add it to my project(SKD...
Why I will restart the ADC is used to measure the voltage is greater than 1.2 V
void battery_start(void)
{
uint32_t err_code;
// Configure ADC
NRF_ADC->INTENSET...
I just assembled my first nRF51822 board and I was able to program it using an IDAP-LINK and a blinky program compiled with the Eclipse/GCC toolchain flashed via SWDIO/SWDCLK...
