Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
I'm developing an UART with SD110. I've updated the SDK to the newest 7.1 and I'm using MDK Pack-Installer.
I found a problem in app_uart.c and retarget.c .
retarget...
I have a nRF24L01+ connecting to an Arduino board using the RF24 library code. It is a print of the registers:
On the nRF51822 I have the following code:
int main...
Hi, I was looking on Digikey and there is a device with the following code: NRF51422-QFAA-R7 V2
Does anyone know what the R7 V2 means? I think R=reel? Thanks
Hello everyone,
I have two nRF51822 (PCA10024) which I want to communicate, one is a peripheral s110 and working properly with a batery service and a custom service, and...
I am new to BT certification so my following question may be incorrectly stated.
We are creating a new OEM BLE module using the nRF51882-CFAC. We intend to sell this module...
Devzone,
I've been working on a central device based on the project 'ble_app_multilink_central' and have encountered an error originating from within the softdevice of...
In Bluetooth 4.1 spec they mentioned scatternet option for BR/EDR topology....not for LE topology...
is that option of connecting to multiple centrals at a time will applicable...
I need a BLE device that can broadcast codes/id to my android mobile app. Also, I need those codes be changed by once in a while by an admin app. Is this possible?
I'm unable to get any output when writing to the UART while using the s110 softdevice. I'm refering to the hardware UART. I'm not using bluetooth for serial.
I'm using...
Hello,
I wrote a firmware for my project, based on the UART over BLE example, so using the softdevice, establishing connections, etc. It works.
I'd now like to use a...
Hi all,
I can program and debug my application just fine when the softdevice is not used (initialized). Problem is, when I do use the softdevice, I end up in Hard Fauld...
Hello,
In our prototype (Embedded System) we want to use nRTF24AP2 with Chip Antenna, as W3006, for example.
Our questions are: where and how needs to be placed the Chip...
Hi there,
I currently have an nRF51 DK set up transmitting six 20 byte packets per 7.5ms, there about, to an nRF51 Dongle set up as a central. When viewing with Master...
Hello,
I would like to move on from using nrf_delay_ms().
I thought this would give me some first results, but It don't. Whats wrong?
//a
static void test_timer_handler...
Should be noted that i'm using nRF51822 breakout board and i have a lot of problems with its programming. And i'd just begun to write own topic about my problems with connection...
