dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi Nordic Devs,
For my project, I am looking for couple of tactile SPST (Single Pole Single Throw) switches like this one . Would appreciate any alternatives that are cost...
Hi!
I realize that the paint on this is still drying, but I'm wondering if anyone is seeing the following behavior?
I can run an program based on this API once. When...
I'm developing a custom solution using the nRF51822 CFAC. The nRF518-SDK version 6.1 does not explicitly claim support for the CFAC. Will there be issues using this SDK and...
In my plan I have a rf moudle NRF24l01 , this is not important, so , If you see in figure 1 we have radio masts that send waves in around. we can't accept this. my plan for...
I have a system where any two identical devices need to establish a communication between each other, without any prior knowledge of which is master and which is slave. Currently...
I have the 51822-DK. I was finally successful in uploading the Heart Rate Monitor example application to the chip with the S110 but now it looks like nothing happens. I downloaded...
Hi nordics.
I am trying to do s120 multilink_central example.
However, this example doesn't work well, and I cannot debug central example.
-Environment-
board...
Hello,
I am working on pca100028 and using s130 softdevice(SDK 6.1.0.0.). I am trying to see UART log on pc. But my code get stuck at the following while loop.
void simple_uart_put...
I am using ATmega32s to drive the nRF24L01+ chips and a low dropout 3.3v regulator (TI’s LP2950) to power the nRF from the five volt buss.
Both the transmitter and receiver...
We are seeing bonding issue between Nexus 6 and our 51822 based product. After inspecting the sniffer capture, we observe that the phone advertises its IO capabilities as...
I have an nrf51822 S110 based application that tries to discover the primary services on the GATT server at every connection of a central.
Unfortunately, the central does...
Hi,
I have read all the answers about ANCS, it seems there is no conclusion can be resolved the problem, that is "It seems working first connection. But after rebooting iOS...
Dears:
I'm using nRF51822 with softdevice S110 . And I want to know, how can I switch the communication mode betwean BLE and 2.4 G ?
If possible, could you provide me...
According to ble specification [1] and based on my test with iOS, the cts_c library seems to have bugs on a process decoding adjust reason data.
Here is a simple diffs...
Hi,
I want to run the experimental_ble_app_uart application on our custom nRF51822 board.
However, I could not find a proper bootloader to start the application. Is...
