Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hello,
I'm currently using Visual Studio Code with the newest SDK, Toolchain and Plugin on MacOS and most of my applications are freestanding applications.
Now I want...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
I read somewhere for new project we should use nrfx driver because in future old nrf_drivers will not be support and improve. All examples in sdk15.3 as I understand used...
Hi All,
I am trying to implement a battery level reading app using NRF52840 DK. It seems I am receiving a timeout from saadc.
In order to run on the Lithium battery, should...
Hi,
I programmed two thingy:91 to return RSRP and RSRQ to a server. On is running with LTE-M and the other with NB-IoT.
I found something that seems strange : +CESQ: 99...
Hey everyone, I'm trying to use the QSPI module (again) to interface to RAM, not FLASH. I'm not really sure if this is possible, but we'll get there. Right now I can't get...
I've been tested for BT SIG however have met error which sent 0xc000 and got 0xc000. I expected to receive 0x8xxx. Command is LETestEnd.
I tested with nRF51822 customer board...
Opening a project in SEGGER Embedded Studio I have annoying "no entry signs" (white minus sign in a red circle) on the left side various items in a project, whereas most of...
Working with nrf52832_mdk and using basic GPIO functionality, I am unable to toggle the GPIO pins P0.0 or P0.1. The code I am using is quite simple and I am able to toggle...
Hello,
I am working on the mqtt sample from ncs\nrf\samples\nrf9160\mqtt_simple. Mostly the nRF9160 connects to the MQTT server in the first attempt. But sometimes I observe...
Hello,
I work on nbiot evaluation and i try to send udp data from my basement.. I boot and attach network from ground-floor and when i'm on PSM mode im going on basement...
I want to run the board at 1.8V and run the uart and spi examples on my laptop. What should be my configurations and which micro-usb port shall I use to connect with laptop...
Hi,
I'm trying to send custom messages between server and client, based on the light switch example. I've modified button_event_handler and the client was able to receive...
Hi Nordic team,
I have an issue: I have to program/flash my mesh application together with softdevice140, mesh-bootloader and device settings page on the nrf52840 chip....
Hi everyone,
I am facing a kind of a strange problem. I want the system to enters system OFF mode when a certain pins goes to LOW. For that reason I have include code section...
I plan to use the nRF52833 or nRF52840 chip and as usual it needs a charger circuitry “PMIC” to charge the battery "Li-Ion"
Is there any special PMIC version recommended...
