We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
nRF52840 NCS 3.0.1 RCP
I just installed the NCS 3.0.1 SDK. I am trying to set up a border router on a Raspberry Pi 4.
I followed these instructions on the Raspberry Pi...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Hello,
Not a 100%, but in this Nordic video the nRF52840 might be using the Alexa Gadgets Toolkit. Alexa Notepad demo 2020 https://www.youtube.com/watch?v=CdLfg-6kQs0
...
Received our 52840 DK, loaded, via nRF Go Studio, s140_nrf52_7.0.1_softdevice.hex. Loaded, via IAR Workbench, ble_app_blinky_pca10056a_s140. I clicked to go button and whamo...
Hello. Nordic team.
Once again I had questions, this time related to serialization .
While the preparation of the driver is on the PC side, I am studying the examples...
I have an issue with reseting the board using a hard reset via an external button. The onboard development kit reset works, but I am trying to perform the same task using...
Hello,
I was reading the nrf_libuarte_async library, and noticed that in the
app_timer_handler -
calls the
local_app_timer_start -
again and starts the timer again...
Hi,
I use a 3rd party board from raytac ( https://www.raytac.com/product/ins.php?index_id=95 ) on my PCB and I have problems with a bluetooth low energy connection. On your...
Hello,
I'm trying to get sleep mode working on a nRF52840-DK with Zephyr or Mbed OS while using UART.
It is possible to achieve low current consumption in sleep mode...
I opened an example from the SDK 16 in:
nRF5_SDK_16.0.0_98a08e2/examples/iot/lwm2m/lwm2m_client/pca10056/s140/ses/iot_lwm2m_client_pca10056_s140.emProject
When I try to...
Hello!
I want to develop my own app, and the source code refer to proximity in nrf toolbox. Now, i have some questions:
1. What function in the source code of serverManager...
Hello
In my application, I would like to allow smartphone that are Bluetooth V5 compatible to receive more information in advertinsing packets from my devices (via the ...
Hi,
I want to optimize the transmission efficiency and thinking of sending larger packets than 2048 bytes of MQTT would help.
We have limited battery power, and looking...
Hi,
I am started working on nRF9160 Power Management. I want to power down all devices(sleep mode) expect motion sensor, Wake if motion is detected. I went through System...
Hi Team,
Can you please point me where I can change the compiler optimization level in SES v4.52 and I am using nRF9160 module.
Regards,
Praveen Palaparthi
Hi Team,
We are using the NRF52840 Device with S140 Soft device for our BLE applications. As part of this we have enabled the flash storage as well.
We are unable to write...
Hello,
I'm using nRF52840 custom board with nRF5 SDK v16.0 and Softdevice v7.0.1.
I can successfully DFU/OTA the device using nRFConnect app. But after DFU is complete...
