Dear Nordic Support Team,
We are in the process of integrating the Nordic nRF Mesh SDK (version 3.3.4) into our custom Java-based application and require your guidance on...
NCS 2.9.1
NRF52840
Sysbuild but with only a single image (no bootloader)
I've been trying to figure out how to change the merged.hex output and how to perform additional...
This stopped working for me... Error is the following
Command failed: git ls-remote --tags --heads github.com/.../sdk-nrf
fatal: unable to access ' github.com/.../'...
Hello,
After a lot of efforts I managed to autoprovision and autoconfigure my nrf52840 board (provisioning and configuring inside the software and not through external app...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Has anyone been able to successfully setup a Segger Embedded Studio project to step through the Bootloader included in the nRF5 SDK for Mesh ( https://infocenter.nordicsemi...
Hello to everyone and thanks in advance.
First of all, im new at this and would i might be asking something stupid.
I have a development, that one of the features would...
I see in NRF5 SDK ShockBurst compatible mode and relevant support.
I dont see such thing in Bluetooth core5 specification. So - ShockBurst is you proprietary creature ?...
I see the messy information elsewhere especially in selling infos about antennas for BLE5. OK optimal antenna is a quarter length of average wavelength -( 299 792 458 ) /...
I ordered nrf52-dk.
I am trying to install the SDK using nrf Connect Desktop using the option below:
Getting Started Assistant Guide to set up the nRF Connect SDK
I...
At least the combination ARM gcc 9.2.0 and nRF5 SDK 16.0.0 prevents me from doing incremental builds after some source file have changed.
The problem is with wrong dependency...
Hello,
I am developing an IEEE802.15.4 Beacon with the nRF52840-DK, SDK 16 and the nRF-IEEE-802.15.4-radio-driver . My problem is that the consumes ~400uA of current in...
Hi,
Good day,
I am having trouble for enabling the SAADC module. I keep getting the following error.
Following is the sd_config.h code
Someone help me solve this...
Hi,
I have read that using the external 32MHz crystal is mandatory for proper BLE radio operation.
However, is there any internal clock that could be used instead of the...
Hi, I am trying the to create a mesh application using iOS nRFMESH SDK. I am able to provision the device but i am not able to get data from the getCompositionData method...
We are using nRF51822 in our custom board.
We just remain two pin ------ SCLK and SWDIO
Can we programming by STLink ?
what's the step?
1.using nrfgo studio to programming...
I tried setting the name as AT+NAME=LGS\r\n
When I send AT+NAME?\r\n, I do read back the new name, i.e. LGS.
However, the bluetooth host continues to see my device as...
Hello, I am using the sim card that comes with the Thingy91 in Sweden, it works well but every time I reflash the thingy with a new version of my application it takes several...
I went through each of the steps for upgrading the thingy91 modem firmware -> application firmware -> 52840 firmware but when I look at the lte link monitor it looks like...
