Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello,
I am using NRF52832 with soft device 13.0.0 and Nordic's bootloader from the examples.
What I do is develop an application which stores some values in uicr registers...
I'm using 52810 with s112 stack.
And I need two PWM channel with different frequence. one channel set to 4KHz to cotroller BEEP, the other one set to 15Khz to control...
Hi, I've completed the first 3 BLE tutorials (about advertising and Services).
I've got notifications up and running on the peripheral by using a timer and hvx as in the...
Hi,
We are developing a mouse . The controller we are using is NRF52832 QFABB0.
You known that its contain 32KB RAM and 256KB of flash memory.
Our application contains...
Dear,
Currently, I can run asset_tracker application with THINGY:91 PCA20035 and I am looking for more examples for this one.
On Thingy:91 FAQ :
@ Peder Rand mentioned...
Hi,
Experimenting on a stepper motor control (DRV8834). I want to be able to send a single square wave output, with a specified number of pulses. I managed to put together...
Hi!
I use SDK15.0 on a central side with nrf52832 with bonding and work with whitelist.
On the peripherial side I use nrf52810.
All works fine, all bonded and work with...
I was successful in flashing the dongle using SWD and the development kit. I used the blinky example. It all works perfectly. However, as soon as I reboot the dongle, it goes...
Dear support team,
I'm using the demo ( thingy52-mesh-provisioning-demo).
And I'm developing the Windows APP as a provisioner/proxy client.
When I send the proxy pdu...
Hi,
I am developing zigbee system using nrf52840.
I have a question about joining process.
a) First, start coordinator with zigbee_erase_persistent_storage(ZB_TRUE)...
I am using a repeated app timer to count the number of seconds that pass from the start of the NRF system powering on (or the code being flashed into the NRF). The code below...
We are developing a mouse with shortcut keys on Nordic, we want to make it compatible both on Win and Mac, but the shortcut key assignments are different between the 2 system...
I am currently developing an HID over Bluetooth device and would like it to be able to determine which OS the host is running so then its beviour changes based on that info...
According to SIG specs the BLE Mesh max payload is = 384 ( 12 * 32)
nrf52 MAXLEN = 255 (but I can transfer 265 bytes in zephyr (259 bytes data + 2 bytes opcode + 4 bytes...
