HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
nRF905 is still manufactured, right? I didnot see anything on Nordicsemi, but I've seen on Farnell's web page "No Longer Manufactured" and on digikey it was not available...
Hi!
I'm using nrf8001 to send twenty 20-byte packets to a phone application. The connection interval I use is 30ms. However, I takes 5 seconds to send the data to the phone...
Hi, I want to advertise each 3times every 5seconds as sometimes beacon scanner can't read it so I need 3times in series advertising.
in main() I added 3times advertising...
Hi there, I am working on NRF52 DK, SDK15.2 with SD 6.1.0, The issue I am facing is that the DFU service is appearing on Android device and I can update apps using NRF toolkit...
I am trying to connect nrf52832 with custom android app, after connection established beacon sends message. Sometimes I can establish the connection after 8 tries, sometimes...
Hi,
I'm working on a project which uses two nRF51822 (SD130 and SDK v11.0) on mobile devices. Device A is continously advertising and device B scans for a fixed interval...
I'm looking to sync an ADC reading with the PWM output. I'm using PPI for this but fails to make it synchronise properly with the PWM.
I'm getting interrupts and sampled...
Hello,i am using nrfsdk with softdevice 6.0.0 in my application and by using it i am trying to connect my mobile uart application with my BLE .but i am facing some issues...
Hallo all
I have an appliation using the LOG for TX output to uart,
I want to maintain this code but to add RX based on the app_fifo_init,
how can they coexist ?
thanks...
Hi,
I would like to use the nrf52 as my bluetooth end device, which inturn has to communicate with the Bluetooth IOT gateway like Rigado module or Nordic gateway APP(which...
Hi
I am using SDK 14.0.0 and soft device S130.
I am planning to add SPI functionality to BLE's sample code.
However, when moving to the next instruction after SPI data...
I am developing a beacon using nrf52810. This beacon will advertise iBeacon as well as Eddystone packets. And user should be able to configure some of the beacon paramters...
Hi Nordic,
I am using the example nrf_app_interactive with nrf52 DK. I am using it as a central while connecting to a peripheral. This peripheral has a lot custom services...
Hi,
I need implement a single Byte transaction on SPIM.
I implemented a stop as documented in
setup_workaround_for_ftpan_58 function
It works only for the first...
