Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi,
I made a custom board with nRF54L15. I do not have a spectrum analyzer, so I cannot tune how much power goes to the antenna or how much is radiated. So, I started ADV...
Hello,
I am using sdk12.2.2 and pca10040. I want to add uart drivers in ble_app_template code so that I can use printf to get my data on terminal. Unfortunately I am not...
I AM USING SDK 12.2 AND IT IS RECOMMENDED TO USE FSTORAGE. But i found no function to read unlike pstorage_load . so can i use pstorage instead of fstorage will it cause any...
Dear Helpers,
We are facing an issue. It is all related to DFU (secure buttonless) and Android 7.0 (deployed on a Samsung A5).
We have a code that is running perfectly...
Hi
By playing around with the serializer code for the S132 5.0.0 I found a bug in the serializer/deserializer code.
The ble_gap_evt_auth_status_t has a new field "lesc...
I'm using FreeRTOS in my project and I wanted to check if the APP UART FIFO implementation is thread safe, IE I want to have a reader and writer thread. Each FIFO has a separate...
I want to enable BLE's NUS Service(in Old SDK, nRF5_SDK) with in nrf5_SDK_for_Mesh.
Is it possible?
I'm failing, as starting of this, to use Softdevice for parallel use...
I HAD ASKED THIS QUESTION: we have used the NRF51822-BEACON KIT EVAL BLUETOOTH SMART BEACON which includes RGB LED, but cannot find a non dev kit model with RGB LEDs . can...
Hello sir,
I have develop project and their lots of quantity. I want flash my updated program into my nordic device without open this device via BLE services. Is it possible...
Found on the web:
"Properly configured WiFi network shouldn’t interfere with the Bluetooth signal. The best practice for WiFi configuration is enabling WiFi on one of the...
Hi
I have a project use nrf52 to have a purpose below.
Maybe after some pairing process with smartphone.
The user can trigger the device(nrf52, may press a button...
Hi guys,
I am trying to connect my BLE Nano 2 with HM-10(as a Peripheral device) using Arduino Central_test program.But the problem is it is not pairing with it,but detecting...
Hello,
We try to use "ATT_MTU" and "Data length extension (DLE)" to expand a packet in S132 SDK 14.0.0.
When we set "ATT_MTU" > "DLE", please tell me what happens?
...
i am in very strange problem and was unable to debug it
i am using following code to write 16 bytes data to flash memory, my app hangs after executing custom_flash_write...
Hi all,
i'm trying to use the function of power warning with s132 and nrf52 with sdk 11.
i use the function
err_code = sd_power_pof_threshold_set( NRF_POWER_THRESHOLD_V27...
