Hi,
I started the LBS example on the nRF52DK_52832 kit and connected the PPK2 kit to the P22 pins for measuring power consumption. I am not sure if I did something wrong...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hi,
I am trying to use nfc_t4t_lib and I have some issues because processing incoming data takes some time (around 100 ms) and therefore sending the response occurs late...
I'm not sure if this is the right place for this question.
I'm using the Settings subsystem for the BLE name.
When BLE is initialized inside matter, settings_load is only...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
Hello,
I am working with S132 3.1.0 on a project based on FreeRTOS. Under some circunstances I set manually the value of some characteristics by using the function sd_ble_gatts_value_set...
Hi,
I am working with a nRF51822 board and I want to program in OTA. I know how to program over the air, but the only problem is that when I have a new unused board I need...
Hi,
I am adding BLE functionality to one of my existing product. I product will play the central role for which I am thinking to use nRF51822 based module.
I learned...
Hello i read RSSI in beacon_evt_handler() hrs_scanner project:
printf("RSSI: %d\n\n\n",p_evt->rcv_adv_packet.adv_data.rssi);
but he show me a wrong value of RSSI: 4539...
Hello, I connected, according to official layout design, a 32 Mhz crystal to my nrf52840. Using a 60 Mhz oscilliscope, I decided that the crystal isn't working (no sine wave...
Hi all,
I'm on 10.11.1 (El Capitan), followed the instructions here
github.com/.../pc-nrfutil
And it looks like installed was happy but when I try and run nrfutil...
Hello,
While porting a C++ application to SDK13.0.0, I ran into weird compiler errors, such as
error: #800: this declaration may not
have extern "C" linkage
...
Hello,
I am using a nRF52832 DK(PCA10040). I am qurious about the output impedance at RF connector "J1" on the PC board. Does it provide 50 ohm output impedance so we can...
Just two questions regarding the new nRF52840 to make sure I've understand it correctly;
For the NFC, this is passive only? So it acts like a tag and is not able...
I've been trying to for two days. Using nrf52DK, SDK12, no SD, Keil5.
All I want is to get printf() to work over ITM/SW/Debug, I'd even accept RTT if I had to. I can't...
Hey I am trying to create a blinky project from scratch on
System: MAC OSX
Eclipse Neon
GCC 4.9
I am trying have it eclipse managed make.
I am at a point when after...
Hi, I was wondering If I need to wait for a response from the server that a command was executed before executing another command or if the BLE stack takes care of this under...
Hello
i m searching for a method to send a big buffer with TWI to a slave. The Buffer is read from flash. because its a soundfile its needed to send the buffer without delay...
I am trying to set up a nrF52 -> Rpi v3 -> Exosite through CoAp as in the nrF5 iot sdk. The nrF52 to rpi works as I am able to ping the nrF52 through its global link address...
