Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hello,
I have few question please about this example.
m_lesc_private_key looks unused, how to modify source to use a pre shared private key ?
is this exemple secured...
Hi!
We are trying a new module with NRF24l01+. We find a troublesome thing. On this video you can see the RF communication starts and stops with a broad-spectrum signal...
Hi :
In my application, i need to use 2 spi master (SPI0,SPI1) and spi slave the same time, but when i compiled drivers_nrf/hal/nrf_spi.h and drivers_nrf/hal/nrf_spis.h...
Hi. I'm using nRF528332, SDK13, S132.
I'm making multi-link peripheral refering to "experimental_ble_app_multiperipheral".
This example code says as below.
#define...
Hi Nordic,
In my application, I want to consume as less power as I can. In the initialization I have this functions:
static void utils_setup(void)
{
APP_TIMER_INIT...
why not provide the ready-made tools？ like micro_ecc_lib_nrf52.lib and nrfutil.
because it 's really take user a lot of time to built these tools.
thank you.
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hello ! I'm beginning work with BLE . I have a project in which nrf51 is a central. App from smartphone will sending to central any key for example "3214941E0" when central...
Hello Nordic community,
I have a question about implementing DFU on the custom board. By looking at NRF52 DK and reading explanation in Nordic infocenter, I can see that...
Hi,
I am have a custom breakout board that uses the NRF52832 chip and I was able to program it using the J-link programmer and seperating ribbon cable to expose the Vtarg...
How do I maximize range for BT5?
I have two nRF52840 pdk units and I have loaded the ble_app_att_mtu_throughput app and tried it out. I have been seeing around 70 meters...
Hi. I tri to use my soft i2c lib
It works well at nrf51 and other mcu's. But nrf52 i2c_read doesnt works properly.
Other funcs works well.
When i read byte from i2c slave...
Hello
in the zephyr 1.7 release there have NRF52 and NRF51 porting without softdevice .
in the SDK 13 ,there has Freertos example working softdevice ,is there any plan...
hello friends :)
i'm trying to make an nRf51822 evaluation board for breadboard
i used 0.1" header and power from usb connector
i'll upload my altium schematic and...
