Hi,
I have question about a project I'm running on nRF connect sdk 2.9.1.
I noticed that whenever an i2c sensor device device_init() is returning a value not equal...
I am trying to run some of the more basic examples included in the nRF Connect SDK on the nRF5340 included in a Thingy:91 X . I have installed the latest version of the nRF...
The OSCILLATORS documentation says:
" The device starts at 64 MHz. For 128 MHz, it must be configured when the CPU starts and before any peripherals that use the high-frequency...
Hello,
I am using nRF54l15 and nRF Connect SDK v2.9.0
I need to know if there is any way to disable the cfg_changed callback at runtime. I want it to be called in case...
I am in the process of getting a Nordic Thingy 91 X up and running for an upcoming development project. However, I’m having some problems getting the Thingy to connect to...
I had to modify the modem_cellular.c file driver in Zephyr to make it work for a SIMCOM modem. I know I could try getting a PR to Zephyr approved but it'll take some time...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hi,
I am wondering whether I can have one "RELAY" device in BLE communication (not BLE mesh), I have look through this forum but only saw some example 5 years ago. As I...
Hello,
We are using a BLE module based on nRF52832 with a U.FL connector for external antenna connection. One of our automated tests requires we turn off/on the antenna...
Hi Support team
1) What is the actual minimum operating temperature of nRF51802?
2) Could you help clarify more details about the temperature sensor(TEMP) of nRF51802...
Hello, I have U-Blox Nora B120 dev boards. Nora B120 chip has built in Skyworks SKY66405-11 FEM IC and I want to use it.
I read in the documentation to copy folder with...
Hello,
To provide some context, I am using an ANNA-B112 with nRF52832 on a custom PCB board we manufactured for evaluation. The nRF52832 is setup with the NUS service with...
Hi,
Our team is trying to disable the Access Port Protection (APPROTECT) for the nRF5340. The main goal for this is to be able to start breakpoint debugging without needing...
Hello,
We’re testing the nRF9160 GNSS performance on our custom PCB and have noticed that, even with A-GPS, the first fix after powering on the device takes significantly...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hello,
I am developing a mesh solution when the nrf52840 USB dongle will act as an observer.
I am using the mesh sensor observer sample. I am able to build and flash...
Hello,
I recently bought a nrf52840 dev kit + dongle to test the functionalities of Matter.
To commission devices "On network" without the use of Bluetooth, i wanted...
Hello,
I'm looking to get XInput working on the nRF52840 so that our device can appear as an Xbox-compatible game controller. I'd appreciate any guidance or recommendations...
I tried the WindowCover sample with the latest SDK 2.9.1, on NRF5340DK.
The sample reports the attribute when manually control the lift.
However, when controlling the...
Hello,
I get "data_len_update failed (err -5)" error message in lesson 3 exercise 2 of Bluetooth course. I have posted the output log below. Any idea why this is happening...
Hello!
I would like to report a bug with the nRF Connect for VS Code extension.
My setup
VS Code v1.98.0
nRF Connect for VS Code Extension Pack v2024.9.5
nRF Connect...
