Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
This thread in zephyr community has left me confused about the features supported. lists.zephyrproject.org/.../31926113 .
Can you please confirm I can advertise and make...
when i try to debug with the segger develoment envrionment using a segger j link
i get the following log and a generic error
this is straightout of the box code no...
Hi ,
I am working on a NFC project which has below requirements , could you please help check if we have any existed example I can test ?
1. Support standarded ISO/IEC...
I'm looking for a nodified 'Wireless UART example" that I can use for a range test.
https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0/wireless_uart_15_4...
Hello,
I have problems using nrFgo Studio with my J-link programmer. The "nrf5x Programming" section is greyed out when the j-link is connected to the PC and the MCU....
I am working on a client to collect data from a continuous glucose monitor. I see that the CGM Service has been part of the SDK for some time. But there is no matching client...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...
Hi--
On dev kit PCA100056, SoftDevice s140, SDK 15.3, in project ble_app_uart_pca10056_s140, we are trying to operate the UART TX/RX characteristic with outgoing payloads...
Hi All,
I'm very new to this Bluetooth mesh technology. Currently I'm referring to client/server switch example.
Without making any changes in the firmware I compiled...
I am seing odd time strings from AT+CCLK... Like: "+CCLK: "15/02/01,00:00:08"\r\nOK\r\n"
I think it is required that AT+CCLK responds error until it has gotten network time...
Hi!
I work at Lund university and I'm preparing a upcoming course project course. The course is about prototyping and PCB design. I want to use the nrf9160 as a example...
I get FDS_SUCCESS after I do fds_write(&desc, &m_dummy_record).
But when I do rc_read = fds_record_find(FILE_ID, REC_KEY, &desc, &tok); I get an error code rc_read = FDS_ERR_NOT_FOUND;...
Hi all,
I am trying to develop an Android app to connect to a nrf52832 running the ble_app_uart example. Previously I was using the Android-nRF-UART codes as a starting...
Hello
I have nRF52840-DK and also a nRF52840 Dongle with me and i have installed SEGGER Embedded Studio with "nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71" SDK downloaded...