i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi Nordic,
my BLE peripheral with the nrf52840 and sdk 15.3 with s140 restarts if not connected after 180s. I assume that the reason is the .config.ble_adv_fast_timeout...
Hi,
I am trying to create a mesh network using nrf52832 for RGB lights. I am using nrf Connect SDK to build the project. Is there any sample code for RGB that can be integrated...
I have found that you cannot update MCUBoot unless you also have the NRF Immutable Secure Bootloader, If i have this then i cannot update the Immutable bootloader.
Is there...
We developed a ble hid mouse using ble_app_hid mouse example. When our mouse used in MAC os scroll wheel function is not working as expected i.e. when we scroll there is only...
Hi, We have an issue with custom devices in the field that have nRF52811, with s112 programmed. To sort out our issue we need to connect to the nRF52811 that is an advertising...
Nordic's BLE page ( https://www.nordicsemi.com/Products/Bluetooth-Low-Energy ) says the nRF5340 is the "ideal choice" for LE Audio. I can't seem to find any information on...
Hallo,
my nRF52840 and my nRF24L01 are receiving the same data in proprietary radio mode.
Several nRF51822 are sending mixed up data.
Within the nRF24L01 - radio Interrupt...
Hi,
I am completly new in nrf52, nrf-connect and zephyr environment.
I need to configure pwm channels that wont be used to drive led...
Most of thing is undestand for...
Sending a PSK like:
AT%CMNG=0,42,3,"1r0nm@n"
should result in failure, as that is not a valid hex string (as documented in nRF91 AT Commands). Currently this results in...
Hello,
I am trying to run the CCS881 sensor sample in my nrf9160 board. I have made changes to my project config file and main.c file as mentioned in
https://devzone...
I need to compare two ble_date_time_t structs to figure out if one is later than the other. So basically I need to check if rtc_datetime > expiration_datetime. Both rtc_datetime...
I plan on writing my own service (similar to NUS) but prior to that, I'd want to use all the existing APIs for initializing the GATT and BLE stack at least
I'm calling the...
Hi Team,
i have trying to create multiple serial port with debug log enabled in the sdk code sample but when i am going to init log_init a long with any UART / SERIAL...
HI
I still try to reconfigure my Zaphyr testing environment to NRF Unity/CMock but I've encountered more issues.
1. __syscall mocking
Is there any reason to exclude...
Hello there,
I'm trying to interface msp430 (master) with nrf51882 (slave) through SPI. I'm running soft device 110 to broadcast the received data from SPI through BLE...
