We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
Hi,
I am unable to find how is software interrupt generated for Softdevice.
I am able to see SD_EVT_IRQHandler()
but when this event is triggered
Sudhir Foujada...
Hi,
I am using sdk for mesh V.5 and nrf52840 dk.
I have run the serial mesh example and it worked fine.
I also modified the light switch example to send and receive...
Hi, I tried using the border router example that is provided and it works ok. I would like to install the border router software right onto a machine running ubuntu so that...
Hello! My device (peripheral) is based on nRF52840. Also, I use nRF52840 DK (central) to establish connections from the Linux side and getting of the data from the device...
Hi all,
is it possible to have the Immediate Alert client and Server at the same time? I need to have an alert from Smartphone and also to be able to send an alert to the...
Hi
In the final SLM version , please provide an option to disable and enable JTAG in software (thru AT command or by some means)
As part of security, this is needed...
Hi,
We are in the process of integrating a NRF52840 to a linux based host gateway device, which is supposed to be the gateway for another peripheral device which also run...
nrf52 dk board TWI SCANNING EXAMPLE INTERFACING WITH EXTERNAL EEPROM
Hi, this is vadivelan
I am working on a task like interfacing external EEPROM memory with nrf52dk...
Hi,
I am currently trying to a DFU where the firmware image is sent to external memory, validated and then copied to flash and executed there. I am doing this with the nrf52840...
Hi while implementing Media Transfer Protocol MTP I wanted to know how many bytes were transmitted by the host on EPOUT. I had to do a bit of research and trial/error - I...
Hi,
SDK : nRF5_SDK_15.2.0_9412b96
I want to perform pairing between mobile app and a device NRF52832 device based on the device serial number.
In other words I want...
Hello,
I come to you because I wanted to recover the GPS data in my project for that I based on the sample agps, however when I launch my project at the time of the reception...
Hello
I had integrated the DFU client stack in ble_thread_dyn_hrs_coap_srv_freertos project.
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8
After clearing all the...
I send AT command:
AT+CPSMS=1,"","","10100010","00100001" Which means active PSM mode with TAU time = 2 minutes, RAT = 1 minutes. I receive: CEREG: 1,"61E6","090A8C15",9...
